The Mk3 Fiesta XR2i initially retained the 1,596 cc (97 cu. in.) CVH engine, albeit now with Bosch K-Jetronic fuel injection and Ford’s EEC-IV engine management system, but in mid-1992, the CVH was replaced by the 1,796 cc (110 cu. in.) DOHC 16-valve Zeta engine, which gave up 5 hp (3.7 kW) in exchange for about 10% more torque. An interesting option on the XR2i and other Mk3 Fiestas was the Lucas-Girling Stop Control System, a two-channel mechanical antilock braking system. (Photo: Ford Motor Company)
Viewed in that light, the Mk1 Fiesta’s simple competence can be seen as the victory it was. In many respects, creating a decent, cheap small car is a bigger challenge than building a winning race car. A racer can be ruthlessly optimized for a single purpose; a mass-market supermini has to perform at least passably well in a multitude of ways for a broad range of buyers. Moreover, in this class, excellence in one area usually brings a corresponding penalty in others. More cargo room means less passenger space; better performance cuts into fuel economy; and the technological solutions that allow bigger, more expensive cars to have their cake and eat it too tend to push the price too high for many B-segment buyers to afford.
All that was even more true in the Mk1 Fiesta’s heyday than it is today, a fact that Ford clearly recognized. The original Fiesta was not an extraordinary car, but that was not its purpose. Its goal was to be good enough, and in that sense, the Fiesta came as close as any car of its time to making a virtue of compromise.
AUTHOR’S NOTE
In July 2023, almost 10 years after the original publication of this article, production of the Ford Fiesta finally ceased after 47 years and more than 20 million cars sold worldwide.
ACKNOWLEDGMENTS
The author would like to thank David Austin, Paul Bennett, John Catlow, Kelvin, Murilee Martin, Bob Segui, Jack Stiling, Sam Tait, and Ford Motor Company Archives for allowing us to use their images in this article.
NOTES ON SOURCES
Our sources on the development and performance of the Fiesta included “AutoTest: Ford Capri 2.8i: Straightforward enjoyment,” Autocar 20 June 1981, reprinted in High Performance Capris Gold Portfolio 1969-1987, ed. R.M. Clarke (Cobham, England: Brooklands Books Ltd., ca. 1990): 88–93; “AutoTest: Ford Fiesta 1000L,” Autocar 27 October 1976: 68–74; “AutoTest: Ford Fiesta 1.1 Ghia: A touch of class,” Autocar 22 October 1983: 46–51; “AutoTest: Ford Fiesta XR2,” Autocar 19 December 1981, reprinted in High Performance Fiestas 1979-1991, ed. R.M. Clarke (Cobham, England: Brooklands Books Ltd., ca. 1992): 22–27; “AutoTest: Ford Fiesta XR2,” Autocar 16 June 1984, reprinted in ibid: 32–37; E. Azplilicueta and A. Andres, “La Familia Ford,” Autopista 6 March 1976: 8–14; “Bag a Bargain!” Classic Ford June 2006: 78–81; “Basic buys (Group test: Bargain Hatchbacks),” What Car? January 1985: 26–34; Patrick Bedard, “Celebrating the Ford Fiesta,” Car and Driver Vol. 22, No. 7 (January 1977): 58–61, 89; “Bericht: 35 Jahre Ford Fiesta: Stilvolle Einkaufstasche,” Auto Scout 24, 3 March 2011, ww2.autoscout24. de, accessed 18 May 2013; “Big Hearted Baby,” Fast Lane November 1987, reprinted in High Performance Fiestas 1979-1991: 48–51; Kevin Blick, “Grudge Match: Ford Fiesta RS Turbo v. Peugeot 205 GTI 1.9,” Performance Car August 1990, reprinted in High Performance Fiestas 1979-1991: 88–95; William Boddy, “Fast Fiesta: The New Ford XR-2,” Motor Sport January 1982: 28, “Ford Fiesta 1.1 ‘S,'” Motor Sport July 1979: 978, “Fun with a Fiesta XR-2,” Motor Sport February 1982: 315, and “The Ford Fiesta 1.3 Ghia — An Appreciation, Motor Sport May 1980: 637; John Bolster, “Fiesta: Ford stir the pudding,” Autosport 17 March 1977: 48, and “Ford’s mini challenge,” Autosport 15 July 1976: 41; J. Bonilla, “Historia Bobcat,” Motor Clásico June 2009: 20–23, and “Imagen deportiva: Super Sport y XR2,” Motor Clásico June 2009: 24–31; Gérard Bordenave, “Ford of Europe, 1967-2003,” Cahiers du GRES [Groupement de Recherches Economiques et Sociales, Université Monteqsquie-Bordeaux and Université des Sciences Sociales Tolouse], Cahier No. 2003-11 (September 2003); “Brief Test: Ford Fiesta 1.1 L Economy,” Motor 31 July 1982: 30–31; Richard Bremner, “Ford Fiesta 1.25,” Autocar 2 December 2005; “Brief Test: Ford Fiesta 1300S,” Motor 8 October 1977; Russell Brookes, “Fireball Fiesta,” Motor 12 May 1979 [nn]; “Butch Baby,” Motor 29 November 1980, reprinted in High Performance Fiestas 1979-1991: 16–18; Rich Ceppos, “4000-mile test of the new Ford Fiesta,” Popular Science Vol. 211, No. 1 (July 1977): 76–77, 134; “Changing Guard (Giant Test: Fiat Uno Selecta -v- Ford Fiesta 1.1 Auto -v- Metro 1.3 Auto), CAR September 1987: 134–141; “City Slickers,” What Car? October 1987: 46–69; “City slickers (Group test: luxury superminis),” What Car? February 1985: 24–28; “Compartif: 13 Sportives de Moins de 45 000 F, Echappement November 1979: 42–63; Dirk-Michael Conradt and Gëtz Leyrer, “Die Kleinen mit der großsen Klappe. Der VW Golf und seine Konkurrenten,” Auto Motor und Sport 10/1979 (9 May 1979): 80-94; Mike Covello, Standard Catalog of Imported Cars 1946-2002, Second Edition (Iola, WI: Krause Publications, 2001); Jesse Crosse, “Moving Up,” Performance Car April 1989, reprinted in High Performance Fiestas 1979-1991: 54–58; “Dauertest: Ford Fiesta 1.1 S: Reifezeugnis: 50.000 km-Dauertest: Wie ausgereift ist der Ford Fiesta?” Auto Motor und Sport 21/1977 (12 October 1977): 36–47; “Documento Exclusivo: Bob-Cat: El Ford Español de la Pequeña Cilindrada,” Autopista 5 January 1974: 19–20; “Duds and Duffers,” CAR November 1986: 178–180; Jim Dunne, “Detroit Report,” Popular Science Vol. 203, No. 4 (October 1973): 40; “Economy Superstars (Group Test: Diesel Superminis),” What Car? September 1985: 34–40; Helmut Eicker, “Teure Technik. Wie Ford den Fiesta baute,” Auto Motor und Sport 21/1976 (13 Oct. 1976): 84-94; “Europe’s Most Successful New Car in History Comes to America” [advertisement], Popular Mechanics Vol. 148, No. 5 (November 1977): 51–53; “Fiesta Special,” Classic Ford June 2006: 66–68; “Fiesta XR2i -v- 205 GTI,” Autocar & Motor 25 October 1989, reprinted in High Performance Fiestas 1979-1991: 64–69; “Ford Fiesta,” A to Z of Classic Cars, Classic & Sports Car, 5 May 2011, www.classicandsportscar. com, accessed 12 June 2013; “Ford Fiesta Ghia,” Road & Track Vol. 28, No. 11 (July 1977): 58–61; the Ford Fiesta Mk 1 website, www.fiesta-mk1. co.uk, last accessed 6 November 2013; “Ford Fiesta 1.4S,” Motor 2 August 1986, reprinted in High Performance Fiestas 1979-1991: 44–47; “Ford Fiesta S,” Car and Driver Vol. 23, No. 1 (July 1977): 91–100; “Ford Fiesta to use dry DCT, while Focus will have planetary auto,” DrivelineNEWS, 9 January 2013, drivelinenews. com, accessed 4 November 2013; “Ford Fight Back (Group Test: Supermini Hatchbacks),” What Car? June 1984: 60–71; Ford Motor Company, “Production of New PowerShift Dual-Clutch Automatic for New 2011 Ford Fiesta” [press release], 29 March 2010; Ford Motor Company Ltd., Cars [brochure FA221/125], September 1987; Cars December ’84 / January ’85 [brochure FA221/103], December 1984; CARS May 1983 [brochure FA221/88], May 1983; “Fiesta 3-door Model Showcases the New Durashift EST Transmission” [press release], 18 June 2003; Ford Cars (All Model Catalogue) July/August 1979 [brochure FA101], June 1979; Ford Cars (All Model Catalogue) [brochure FA221/58], June 1980; Ford Cars (All Model Catalogue) [brochure FA101], January 1981; Ford Cars (All Model Catalogue) [brochure FA 211/68], June 1981; Ford Cars (All Model Catalogue October-November 1982) [brochure FA221/83], September 1982; “The New Ford Fiesta, Oh what a beautiful baby!” [brochure FA 254], c. February 1977; “The new Ford Fiesta: Oh what a beautiful baby!” [advertisement] CAR March 1977: 1–2; “The new Fiesta 1300. Now the little car thinks even bigger,” advertisement, 1984; Ford-Werke AG, “Ford Fiesta,” brochure No. 60115, August 1976; “Ford’s happy event,” Autocar 17 July 1976: 12–21; “Fun in a Fiesta,” What Car? August 1990, reprinted in High Performance Fiestas 1979-1991: 87; Jack Galusha, “Ford Fiesta 1.6,” Autocar 21 March 2005; “Geared for success,” What Car May 1979: 17–24; “Giant Test: Fiat 127 Sport -v- Ford Fiesta 1.1S -v- Peugeot 104 ZS,” CAR March 1979: 58–67; “Giant Test: Ford Fiesta XR2 -v- MG Metro Turbo -v- Peugeot 205 GTi,” CAR December 1984: 136–145; “Giant Test: MG Metro -v- Ford Fiesta XR2 -v- Fiat 127GT,” CAR October 1982: 80–86; “Giant Test: Fiat Panda -v- Ford Fiesta 1.0 -v- Austin Metro 1.0,” CAR October 1981: 64-71; “Giant Test Special: Finding Out,” CAR April 1989: 104–118; “Giant Test Special: Renault 5TX -v- MG Metro -v- Ford Fiesta XR2 -v- Citroën Vista GT -v- Fiat 127GT,” CAR June 1983: 108–116; “Giant Test: The Joker Wins: Skoda Favorit 136 LX -v- Ford Fiesta 1.0 Popular,” CAR December 1989: 128–135; “Giant Test: Town & Country Club,” CAR August 1994: 104–121; “Giant Test: VW Polo -v- Peugeot 104 -v- Ford Fiesta -v- Renault 5 -v- Fiat 127 -v- Mini 1000,” CAR March 1977: 42–49; “Great X-packtations,” Motor 17 November 1979, reprinted in High Performance Capris Gold Portfolio 1969-1987: 80–81; “Group Test: Triple Blast,” Motor 7 July 1984: 10–15; David Halberstam, The Reckoning (New York: William Morrow and Company, 1986); Chris Harvey, “The Cars: Keith Ripp,” Auto Performance March 1983: 41–45; Fred Henderson, “Looking Back?” Cars and Car Conversions October 1980: 74–75; Kim Henson, “Buyer’s Guide: MkI Fiesta,” Classic Ford February 2005: 92–98; Tony Hogg, “Healey Fiesta: Donald Healey works his magic,” Road & Track Vol. 30, No. 12 (August 1979): 38–40; Friedbert Holz, “Grosse Klasse, Kleine Masse (Vergleichstest: Ford Fiesta 1300S – Renault 5 TS),” Sport Auto January 1980: 82–86; Dave Holls and Michael Lamm, A Century of Automotive Style: 100 Years of American Car Design (Stockton, CA: Lamm-Morada Publishing Co. Inc., 1997); Paul Horrell, “Newcomers: Ford Fiesta,” CAR November 1995: 196, 199; Mark Hughes, “Fiesta Frolics” and “Is there a quicker Fiesta?” Autosport 20 May 1982, reprinted in High Performance Fiestas 1979-1991: 28–29; Ray Hutton, “Ford Fiesta: Ford’s small success gets bigger,” Car and Driver Vol. 34, No. 11 (May 1989): 38; Lee Iacocca with William Novak, Iacocca: An Autobiography (New York: Bantam Books, 1984); L.A. Izquierdo, “Marketing y competición: Fiesta 1600 Gr.2,” Motor Clásico June 2009: 34–39; Erik Johnson, “2014 Ford Fiesta 1.0L EcoBoost,” Car and Driver November 2012, www.caranddriver. com, accessed 4 November 2013; and “2014 Ford Fiesta Sedan and Hatchback,” ibid, www.caranddriver. com, accessed 4 November 2013; Graham Jones, “The Specials,” Cars and Car Conversions June 1982: 30–34; Jeff Koch, “Healey Fiesta,” Hemmings Sports & Exotic Car #13 (September 2006); Tony Kyd, “12,000 Miles On: Taut Fiesta,” Motor 4 February 1978: 34–36; Michael Lamm, “Driving the Ford Fiesta,” Popular Mechanics Vol. 148, No. 1 (July 1977): 54–56; Damon Lavrinc, “Tokyo 2007 Preview: Honda showing CR-Z Concept,” Autoblog, 9 October 2007, www.autoblog. com, accessed 25 December 2013; Barry Lee, “Laying It on the Line,” Cars and Car Conversions April 1978: 46–48, and “Laying It on the Line,” Cars and Car Conversions May 1978: 47–49; Götz Leyrer, “Der große Preis: Fiesta Super,” Auto Motor und Sport 11/1979 (23 May 1979): 38-45; Annamaria Lösch, ed., World Cars 1979 (Rome: L’Editrice dell’Automobile LEA/New York: Herald Books, 1979), and World Cars 1985 (New York: Herald Books, 1985); Robert Lund, “Detroit Listening Post,” Popular Mechanics Vol. 149, No. 2 (February 1978): 44; MAC, “Smooth New Ford Automatics for Fiesta and Fusion,” Carpages, 30 January 2004, www.carpages. co.uk, accessed 4 November 2013; James May, “Long Term: Ford Fiesta RS Turbo,” Autocar & Motor 17 April 1991, reprinted in High Performance Fiestas 1979-1991: 96–99; Neil McIntee, “Hot Metal,” Autocar 3 August 1988: 42–49; Russell Martin, “Seal of Approval,” Classic Ford July 2006: 84–87; Mike McCarthy, “Fast and Furious,” Autosport 31 January 1985, reprinted in High Performance Fiestas 1979-1991: 42–43; Alex Meredith, “SIA Interview: Donald Healey,” Special Interest Autos No. 67 (February 1982): 58–62; “Metro v. Fiesta: Wheel to Wheel comparison,” Autocar 28 February 1981: 20–24; “Neuheiten: Fiesta Super S/Escort 1980,” Auto Zeitung 23 July 1980: 20; “New Fiesta GL – the finishing touch” [advertisement] CAR March 1980: 10; Paul Niedermeyer, “Curbside Classic: 1978 Ford Fiesta — Here Today, Gone Tomorrow,” Curbside Classic, 26 February 2013, www.curbsideclassic. com/ curbside-classics-american/ curbside-classic-1978-ford-fiesta- here-today-gone-tomorrow/, accessed 18 May 2013; Jan P. Norbye, “The new logic in small-car engineering,” Popular Science Vol. 206, No. 2 (February 1975): 56–59, and “The View Down the Road,” Popular Science Vol. 205, No. 6 (December 1974): 37; Jan P. Norbye and Jim Dunne, “Economy imports: for people serious about saving fuel,” Popular Science Vol. 205, No. 1 (July 1974): 30–43; Jason O’Halloran, “Q Jumping,” Classic Ford October 2003: 8–13; “Oh, you beautiful baby! New ‘Series X’ small wheel arch kit for your Fiesta” [Advertisement] CAR March 1979: 12; “Olé XR2: New sporting model for Fiesta,” Autocar 5 September 1981, reprinted in High Performance Fiestas 1979-1991: 19; “Overtaking Notes No. 14: Ford Fiesta,” CAR November 1995: 13; Ed Pearson, “Goin’ racing: Fiesta Race Championship 1981,” Popular Motoring May 1981 [nn]; Jon Quirk, “Ford Fiesta 1.4 TDCi,” Autocar 20 January 2006; “Road Test: Ford Fiesta 1.1L Five-Speed,” Motor 7 January 1984: 10–13; Productioncars.com, Book of Automobile Production and Sales Figures, 1945-2005 (N.p.: 2006); “Road Test: Ford Escort 1.3L,” Motor 3 January 1987: 10–15; “Road Test: Ford Fiesta 1.3 GL,” Motor Road Tests 1980: 162–165; Graham Robson, “Closing Time,” Classic Ford July 2006: 74–77, and “Lady Killers,” Classic Ford March 2002: 44–48; Ian Sadler, “Class of ’84,” Cars and Car Conversions September 1984, reprinted in High Performance Fiestas 1979-1991: 38–41, “Roadrunner,” Cars and Car Conversions September 1981, reprinted in ibid: 20–21, and “The Pretenders….” Cars and Car Conversions May 1982: 14, 81–82; Ian Sadler, et al, “Ford Fiesta: A EuroKid comes of age…” Cars and Car Conversions September 1980, reprinted in ibid: 5–11; David Scott, “Breakthrough in anti-skid technology,” Popular Science Vol. 229, No. 3 (September 1986): 93, and “Coming: skid control for small cars,” Popular Science Vol. 224, No. 1 (January 1984): 68–69; Werner Schrut, “Kölns Kleinster: Wie gut ist der neue Mini von Ford?” Auto Motor und Sport 14/1976 (7 July 1976): 32–42; Edouard Seidler, Let’s Call It Fiesta: The autobiography of Ford’s Fiesta (Newfoundland, NJ: Haessner Pub., 1976); Bob Segui, “The Last Healey,” Retro-Speed, n.d., www.retro-speed. co.uk, last accessed 1 November 2013; Senate and House of Representatives of the United States of America in Congress assembled, “Energy Policy and Conservation Act,” Public Law 94–163, Title V (Part A – Improving Automotive Fuel Economy), 22 Dec. 1975; Keith Seume, “Rippy’s back!” Hot Car May 1981 [nn]; Andrew Shanks, “Plans for a Fiesta,” Autocar 17 July 1976: 20–21; Don Sherman, “The Econoboxes: All the small cars that are fit to drive, Part One,” Car and Driver Vol. 24, No. 1 (July 1978): 33–56; Dennis Siamanitis, “Ford’s New Escort: Some Technical Tidbits,” Road & Track Vol. 31, No. 11 (July 1980): 77–80; “Smalls of the Line,” CAR July 1990: 120–129; “Sonderserie Ford Fiesta Special: Erinnerungen an Monte Carlo,” Rallye Racing September 1979: 59; Ollie Stallwood, “Ford Fiesta 1.4i Style+ Auto,” Autocar 29 June 2009; “Star Road Test: Ford Fiesta S,” Motor 5 February 1977: 4–9; “T for 2,” Auto Performance October 1982: 81; Alexander Stoklosa, “2014 Ford Fiesta 1.6L S Sedan / Hatchback,” Car and Driver July 2013, www.caranddriver. com, accessed 4 November 2013; “Supersport [Part One],” Performance Ford December 1989, reprinted in High Performance Fiestas 1979-1991: 70–73; “Supersport: Part Two: Restoration,” Performance Ford January 1990, reprinted in ibid: 74–77; “Test Extra: Ford Fiesta 1.6S 3-dr,” Autocar & Motor 12 July 1989, reprinted in High Performance Fiestas 1979-1991: 59–61; “Test Extra: Ford Fiesta RS Turbo,” Autocar & Motor 20 June 1990, reprinted in ibid: 78–83; “Testing for fun,” CAR September 1990: 84–95; “Test Update: Second Chance,” Autocar 25 December 1985: 18–21; “The Autocar Road Test: Ford Fiesta XR2i 16V,” Autocar & Motor 8 July 1992: 36–39; Mark Theobald, “Tom Tjaarda 1934-present,” Coachbuilt, 2004, www.coachbuilt. com, accessed 18 May 2013; “The X Factor,” Cars and Car Conversions January 1980, reprinted in High Performance Capris Gold Portfolio 1969-1987: 101–102; “3 Car comparison test,” Popular Motoring May 1980: 38–41; the Tjaarda Design website, www.tomtjaardadesign. com/portfolio.html, accessed 18 May 2013; “Variable Appeal (Road Test: Ford Fiesta 1.1 Ghia Auto),” Autocar 20 May 1987: 42–49; David Vivian, “Ford Fiesta 1.6 TDCi,” Autocar 30 November 2004, “Ford Fiesta ST,” Autocar 23 November 2004, and “XR2i,” Autocar 15 February 1989, reprinted in High Performance Fiestas 1979-1991: 52–53; Ron Wakefield, “Ford Fiesta: Henry builds a minicar,” Road & Track Vol. 28, No. 2 (October 1976): 34–36; Gavin Ward, “Ford Fiesta,” Auto Express, 9 March 2004, www.autoexpress. co.uk, accessed 4 November 2013; Jeremy Walton, Escort Mk 1, 2 & 3: The Development & Competition History (Sparkford, Somerset: Haynes Publishing Group, 1985); “Ford’s FWD rally Fiesta with a 4-WD secret,” Motor Sport March 1979: 319–321, and “Tuning Topics: Promising Capri and Fiesta Developments,” Motor Sport April 1978: 440–444; Mark Wan, “Ford Fiesta,” AutoZine, 29 November 1999, www.autozine. org/ Archive/Ford/old/ Fiesta_1999.html, accessed 4 November 2013, “Ford Fiesta,” AutoZine, 20 January 2002, www.autozine. org/ Archive/Ford/old/ Fiesta_2001.html, accessed 4 November 2013, and “Ford Fiesta,” AutoZine, 29 September 2008 to 20 March 2013, www.autozine. org/ Archive/Ford/new/ Fiesta_2008.html, accessed 4 November 2013; Ian Wearing, “At last, a worthy sporting Fiesta,” Performance Car August 1990, reprinted in High Performance Fiestas 1979-1991: 95; Rory White, “Common Ford Fiesta problems,” What Car? 5 February 2013, www.whatcar. com, accessed 4 November 2013; Klaus Wießmann, “Aufwertung: Neues Modell mit 1,3 Liter 66 PS-Motor,” Auto Motor und Sport 22/1977 (26 October 1977): 108–112; “Wild Bunch (Group Test: Ford Fiesta XR2, MG Metro Turbo, Peugeot 205 GTi),” What Car? August 1984: 40–44; www.fueleconomy.gov, last accessed 16 January 2017; “Year of the Fiesta,” Rally Sport March 1979, reprinted in High Performance Fiestas 1979-1991: 12–15, 19; and Stephan Zander, www.fiesta1.de, last accessed 5 November 2013.
Some additional information on the Fiesta’s antecedents and leading rivals came from “A curious move in car-engine design,” New Scientist Vol. 15, No. 306 (27 September 1962): 663; Keith Adams and Ian Nicholls, “The cars: Mini development history, part 1,” AROnline, 5 August 2011, www.aronline. co.uk, last accessed 18 June 2013; the Auto Editors of Consumer Guide, Cars That Never Were: The Prototypes (Skokie, IL: Publications International, 1981); “AutoTest: Ford Escort 1100 3-door,” Autocar 27 September 1980: 36–39; “AutoTest: Ford Escort 1.3 Ghia (1,297 c.c.),” Autocar 22 March 1975: 47–51; John R. Bond, “Which Way Our Car? Part II: The Cardinal, Ford’s New Small Car,” Car Life Vol. 9, No. 6 (July 1962): 60–61; “Giant Test: Ford Escort 1.3GL -v- Opel Kadett 1.3S -v- VW Golf 1.3LS,” CAR December 1980: 62–68; “AutoTest: Ford Escort 1300 Ghia 5-door,” Autocar 27 September 1980: 30–35; “Escort Mexico,” Autocar 10 December 1970: 47–49; “Brief Test: Escort 1100L,” Motor 8 March 1975: nn; Arch Brown, Richard Langworth, and the Auto Editors of Consumer Guide, “1959-1997 Austin/Morris Mini,” Great Cars of the 20th Century (Lincolnwood, IL: Publications International, Ltd., 1998): 278–281; Roger Carr, “Car Carshow Classic: 1960 Austin Seven (Mini) – The Future Started Here,” Curbside Classic, 16 December 2014, www.curbsideclassic. com/ curbside-classics-european/ car-carshow-classic-1960-austin-seven- the-future-started-here/, accessed 16 December 2014; “Ford Escort: 40 Years,” Ford Anniversaries 2008, Ford of Europe, www.fordmedia. eu, retrieved 10 January 2010; “Ford Anglia 1200 Estate Car 1,198 c.c. (Autocar Road Test No. 2040),” Autocar 13 August 1965: 303–308; “Ford OSI 20m TS Website,” n.d., www.osi20mts .com, accessed 18 May 2013; the German-language classic Ford Taunus website, www.fordtaunus. de, accessed 7 June 2013; “Ford Taunus 12M(P4),” Classic & Sports Car, 28 March 2011, www.classicandsportscar. com, accessed 25 May 2013; “Group Test: Austin Allegro 1100, Fiat 128, Ford Escort 1300 XL, Honda Civic,” Motor 20 October 1973: 54–60; “Giant Test: Austin 1300 Super De Luxe, Ford Escort 1300 Super, Hillman Avenger Super, Vauxhall Viva SL,” CAR July 1970: 62–69, 87; “Giant Test: Fiat 127DL, Renault 5TL, VW Polo N,” CAR August 1975: 48–56; “Giant Test: Ford Escort 1.3GL -v- Opel Kadett 1.3S -v- VW Golf 1.3LS,” CAR December 1980: 62–68; “Giant Test New Car Analysis 3: Escort 1300L, Avenger S1600, Renault 12TL,” CAR April 1975: 62–69; “Giant Test: Renault 11GTL -v- Austin Maestro 1.3L -v- Ford Escort 1.3GL,” CAR September 1983: 106–113, 119–120; “Giant Test: Toyota 1000, Fiat 127, Mini 1000,” CAR February 1975: 68–74; David Knowles, MG: The Untold Story (Osceola, WI: Motorbooks International, 1997); Richard M. Langworth, The Thunderbird Story: Personal Luxury (Osceola, WI: Motorbooks International, 1980); John Lee, “1953 Oldsmobile Fiesta: When the Dream Came Alive….” Special Interest Autos No. 106 (July-August 1988): 36–41, 65; Brian Long, Porsche 914 & 914-6: The Definitive History of the Road & Competition Cars (Dorchester, Dorset: Veloce Publishing Ltd., 2011); Paul Niedermeyer, “Curbside Classic: Austin Mini – Yesterday’s Mini, Today’s Micro,” Curbside Classic, 16 May 2011, www.curbsideclassic. com/ curbside-classics-european/ curbside-classic-1959-week-mini- yesterdays-mini-todays-micro/, accessed 16 May 2011; Jan P. Norbye, “False Starts and Second Guesses,” Special Interest Autos No. 54 (December 1979): 20–25; “Penny-a-mile Motoring Part I,” Autocar 6 April 1974: 24–29; Pew Environment Group, The, “History of Fuel Economy: One Decade of Innovation, Two Decades of Inaction,” Pew Charitable Trusts Clean Energy Program, April 2011, www.pewtrusts. org/~/media/ assets/2011/04/ history-of-fuel-economy-clean-energy-factsheet.pdf, last accessed 15 January 2017; “Preise der neuen VW-Modelle Jahrgang 1977,” Auto Motor und Sport 16/1976 (6 August 1976): 14; Chris Rees, Essential Ford Capri: The Cars and Their Story 1969-87 (Bideford, Devon: Bay View Books Ltd., 1997); “Road Test: Ford Escort 1.4GL,” Motor 29 March 1986: 10–13; “Road Test: Ford Escort Sport 1600 2-Door,” Motor 8 March 1975: 2–7; Graham Robson, Cortina: The Story of Ford’s Best-Seller, Second Edition (Dorchester, Dorset: Veloce Publishing Ltd., 2007); Graham Robson and the Auto Editors of Consumer Guide, Volkswagen Chronicle (Lincolnwood, IL: Publications International, Ltd., 1996); Heinz P. Schlichting, “Road Testing Ford’s Cardinal,” Popular Mechanics Vol. 118, No. 6 (December 1962): 84–87; LJK Setright, “Fly Babies,” CAR April 1980: 66–70, and “Will there ever be a better mini than the Mini?” CAR May 1992: 90–97; Mary Wilkins and Franck Hill, American Business Abroad, Ford on Six Continents (Detroit: Wayne State University Press, 1964); and “Wizardry on wheels” [advertisement 9/13R], The Motor 2 September 1959: 46–47.
Some historical exchange rate data for the dollar and European currencies came from Lawrence H. Officer, “Exchange Rates Between the United States Dollar and Forty-one Currencies” (2011, MeasuringWorth, https://www.measuringworth.org/exchangeglobal/, used with permission). Exchange rate values cited in the text represent the approximate dollar equivalent of prices in non-U.S. currencies, not contemporary U.S. suggested retail prices, which are cited separately. Please note that all equivalencies cited herein are approximate and provided solely for the reader’s general information and reference — this is an automotive history, not a treatise on currency trading or the value of money, and nothing in this article should be taken as financial advice of any kind!
RELATED ARTICLES
- Ford Cardinal, Taunus, and Prelate: The First FWD Fords
- Cheap and Cheerful: The European Ford Capri
- Compact Cult Classic: The 1984-1991 Honda CRX
- Five by Five: The Renault 5 and the Mid-Engine Renault 5 Turbo
- Tiny and Triumphant: The Original Morris / Austin Mini
- Rabbit Rocket: The Volkswagen Golf GTI and Rabbit GTI
- Short, Sharpish, Chopped: The Peugeot 104 Coupe
- Supermini: The Autobianchi A112 Abarth
- The Salesman and the Statistician: Robert McNamara, Lee Iacocca, and the Ford Falcon
This very well researched paper prompts memories of our rental of a Fiesta in May, 1988 with which we toured Germany and France. I was already a fan of small cars and I found this one to be simple but quite satisfactory. I even drove it through Paris. It certainly was not fast, but I recollect that it could get 40 miles to the gallon. The one problem was finding the unleaded fuel that it required. Especially in France, this was very difficult. One final recollection: cars still had the right of way over pedestrians over there then. As a pedestrian I did not like it and came close to some fights after nearly being ran over. I like to credit my actiions with changing the law to favor pedestrians.
In a SIA’s article “False Starts and Second Guesses”, the author Jan P. Norbye talked about a ford’s small world car in 1963 but he said no more with its layout (was it already a fwd cars?) Could you tell me more with this project?
Unfortunately, that article really doesn’t say much about that project other than that it came from the Ford styling studio in Dearborn around 1965.
As I mentioned on the first page, Ford was talking on and off about doing some kind of microcar for emerging markets. That would not have been a B-segment car like the Fiesta, but something more along the lines of the modern Tata Nano — a very simple, austerely finished car with seats for four and a top speed of 90 to 100 km/h. My guess is that the study to which Norbye was referring was probably one iteration of that idea, which Ford kept playing with (in various forms) at least into the late ’70s.
Thank you for your response. The Ford’s idea about an emerging market’s car was very advanced for 60’s. Good article and topic, I like these car because my grandfather owned a blue fiesta MK1, a very well-looking and reliable car. Ford had done a good comeback to FWD technology.
Thrilled to see this article. I’m a small car nut and love the Fiesta in particular. Four wheels, some vinyl and stick shift protruding through the floor is the recipe for automotive bliss. I wish we would have got the XR2 in the states but they can now be imported. All you need is the willingness to pay far more for something than its worth, I think I’ve demonstrated sufficient lack of judgment to qualify.
Hee — truer words…
There is something sort of compelling about no-frills cars. In practice, it’s hard not to eventually be lured by convenience features (which is why so many modern Bs have power windows and optional satnav), but a well-sorted, no-nonsense basic vehicle has its own satisfactions.
If I may digress about the Ford Taunus . . .
At some point in the last 45 or so years, there was a very detailed magazine article about the gestation of the Cardinal/Taunus–I wish I had the precise citation, but I’ll have to go from memory.
At the time Dearborn launched the Cardinal/Taunus project, Ford Köln had a subcompact fairly far along in development: front engine, rear drive, 1.0-liter OHC I4. It would have been the world’s first production car with the camshaft driven by a toothed belt, but Dearborn shoved the Cardinal/Taunus down Köln’s throat, so that distinction went to the Glas GT instead.
The feeling at this time was that a FWD car with longitudinal engine needed to have a very short engine, and that had been true of virtually all such cars: flat twins (Panhard, Citroen 2CV), triples (Saab, DKW, Wartburg), H4’s (Lloyd Arabella, Goliath). Hence the V4.
The original plan was to have a “Ponypak,” as they called it–engine, transmission, and front suspension as a module that could be removed and replaced whole. This proved to be a dead end, with NVH problems. The writer went so far as to say, “The Ponypak’s fractious behavior was jeopardizing the entire program.”
Ford U.S. also wanted to use single-leaf rear springs, and there was a question of whether they could be sourced in Germany at all.
Saab 93’s were used as mules–a nice historical irony in that a few years later, Saab began using the Taunus V4. The 93 front clip hadn’t been designed with the V4 in mind, so the engineers mounted the headlights in pods on the extreme left and right, and they must have looked even odder than stock 93’s. When Henry Ford II swung through and saw one of the mules, he did a double-take. He said he wanted the car ready by such and such year, and after he left, one of the engineers realized that he’d meant the model year, not the calendar year, which meant that much less time.
The Cardinal version was canceled because it would have had almost the sticker price of a Falcon. The engineers in Köln had their marching orders and got the Taunus production-ready, but it was a sore subject with them for years afterward.
A couple of additions to this:
From what I read, the Cardinal’s design had its roots in a proposal Ford-Werke had offered around 1957, when Ford started thinking about doing a compact car; Dearborn had solicited proposals from Cologne and Dagenham as well as a couple of internal studies. (One of the principal creators of the German design, incidentally, was August Momberger, formerly of Borgward, which probably had much to do with their thinking on FWD.) That project sort of stalled for a while, so Cologne moved onto their own FR design. In the interim, Dearborn more or less started over, borrowing some ideas from the German concept and giving them a new spin, which I assume is why Cologne wasn’t necessarily happy with the results.
With the Fiesta, I think it was really to Ford’s great benefit that other manufacturers had already established a degree of orthodoxy in that segment. The problem with moving into uncharted territory is that you end up with an odd mix of what the engineers think is clever and what the accountants think is affordable (the Corvair being a case in point). By the time Ford started working on the Bobcat project, buyers had a pretty clear idea what they could expect and what they wanted, so every time the project started going in an odd direction, the marketing clinics returned a resounding “Nope.” (Ford clung for a remarkably long time to the idea of a RWD B and I think they only gave up on it because the clinic results were pretty uniformly negative.) Of course, marketing studies aren’t the end all, be all of product development, and it is possible for a good idea to be “clincked to death,” but such studies can be a useful guide to what NOT to do.
Since August Momberger had been with Borgward, I assume he’d worked on the Lloyd and Goliath?
Presumably, yeah. I don’t know what the timeline of his Borgward career had been, but Ford engineers were very conscious of the Goliath, in particular, during the Cardinal project.
The article I mentioned turned out to be “The Ford Fiesta’s Godfather” by Karl Ludivigsen, in the August-October 1977 issue of Special-Interest Autos. Aaron gave me a bibliographic citation for it, but he couldn’t confirm that it was the same article because the Los Angeles Public Library’s copy had gone missing. However, my local library had it. Fittingly, it was published when the Fiesta was introduced in the United States. If this topic in general interests you, it’s an excellent read.
Regarding Escort front suspension, only the very early cars used a compression link behind the axle line.Very soon they reverted to using a front anti-roll bar ahead of the axle to locate the track control arm.
My impression was that when the Mk1 Escort got the front anti-roll bar across the board in 1969 (if I recall correctly, the German cars may have had that from the start), they still had the compression link — the anti-roll bar ahead of the axle line, the compression link behind it. I may be reading it wrong; I’ll check on that.
On further investigation, I think you’re correct. (I had gotten it in my head that the compression links were retained with the anti-roll bar.) I’ve amended the text.
I have very found memories of the MK3 as was ferried about as a child in one around London. Also I passed my driving test on a nearly new MK7 facelift I really like the flexibility and performance of 1.0 ecoboost a relatively nippy car considering it 0-60 was mid 9 secs I do have a fondness for fords.
Another great article Aaron, and this one dear to my heart. In 1979 I bought a 78 “S” model that had been a demo with 12k miles on it. It was a daily driver until 1985 when it became too small for our family of triplets and it became an autocrosser until I sold it to a friend/competitor in 1991. One correction I would like to make is regarding the rear suspension. It was a bit of an oddity and did not use 4 trailing links as stated in the article. It used 2 lower trailing links connecting below the axle, but there were no uppers. control of rocking motion of the axle was done with a bracket on the coilover damper. The damper was connected to a bracket behind and below the axle in normal fashion, while the aforementioned bracket attached to a peg sticking up out of the top of the axle, isolated by a large rubber bushing. The lower part of the damper was a bit stouter than normal to allow it to do this double duty. Not having the upper links also allowed for a bit more room in the back seat area, and I can positively state that one can indeed get 3 baby seats side by side in the back of a Mk1 Fiesta! Do keep up your great work sir, I look forward with anticipation to reading your stories!
Joe Dunlap
Joe,
Your comment pointed out to me that the reference to “four trailing links” was actually an error I didn’t catch while I was putting together the article. Your description is right: there were two lower trailing arms, each of which was slotted to reduce its weight, and lateral location was handled by a Panhard rod on a rubber-bushed peg from the axle beam. I deleted the word “four” from the text, as the rest is correct. Thanks for the correction — I had missed that during the editing.
At some point Road & Track included the U.S. Fiesta in a group test. Their take on it was that in spite of its humble spec (pushrods, dead beam rear axle) it was a lot of fun to drive. Sounds like a Saab 96, although I doubt that it had the 96’s passive safety.
Certainly at that point there was no particular shame in either pushrods or a beam axle. A lot of B-segment cars still use a dead axle (albeit now generally a torsion beam, which the Fiesta didn’t get until the Mk3) and quite a few had pushrod engines into the ’90s. For the era, the Kent engine was pretty competent; the U.S. car was very mildly tuned for emissions reasons, but the crossflow head design gave it a good balance of rev potential and mid-range torque. The nominally more sophisticated CVH engines that replaced it were not necessarily an improvement, despite having a higher specific output.
The Kent engine in its iteration in the US spec Fiesta was truly strangled compared to its European brethen. At first glance, looking at one disassembled and layed out on a table, one would think they were looking at a diesel engine. The cylinder head had no combustion cambers, all of that was in the tops of the pistons. The head was flat on the bottom and the valves themselves were smaller than the Euro version. The intake manifold was also compromised by the close proximity of the firewall making for very tight corners and narrow passages fed by a, as I recall, 28/32 Weber (or Holley knockoff). My personal fix for it (on my miserably small budget) was a bigger valve head from a 71 Pinto 1.6 and higher compression (smaller combustion chamber) pistons and a hand fabricated intake manifold with a pair of 1.5″ S.U. carburetors from a Volvo 122. Sort of a whoopee cushion of a car, but great fun to autocross!
All the five-bearing Kent engines, at least the regular-production variety, had Heron-type “bowl-in-piston” combustion chambers — that wasn’t exclusive to the U.S. version. (The Valencia version had wedge chambers instead.) The U.S. cars did have smaller valves, although they did indeed have Weber carburetors; Ford tried some cheaper alternatives, but concluded that they didn’t work as well.
The restricted breathing did have some payoff in mid-range torque, which is reflected in the U.S. cars’ acceleration times, though obviously it wasn’t a great boon to maximum horsepower, as the people trying to run Fiestas in Group 1 could attest. I suspect (though I don’t know for sure) that part of the rationale of the Fiesta X in ’79 was to help Ford homologate the better-breathing Mexico-style head.
The Valencia must have been used in the Pinto, as thats what the head was like that I found. It had a small wedge chamber, so with the smaller bowl pistons I found, the change in compression ratio must have been a wash. (I never did bother checking as there was nothing I could do about it economically). It seemed to run just fine on regular gas, although I treated it to premium on track days. :-).
The early Pinto 1.6 used the Kent engine, not the Valencia, which came later. The Valencia engine (a misnomer, really, because not all of them were built in Spain) had similar architecture, but had a shorter block and reduced bore spacing; the Kent engines had a common 80.978mm bore while the Valencia was standardized around a 73.96mm bore. (Most of the Valencia engines had three main bearings, but in the latter eighties Ford did a five-bearing 1,297 cc version as a price-leader for the Escort and Orion.) For that reason, I don’t think a Valencia head would fit the Kent block.
I don’t know offhand if the version of the 1.6-liter Kent used in the U.S. Pintos and Capri had a different head, although that’s a possibility. The 1971 federal engine had 8.4 compression while the British versions were generally 9.0:1 and needed premium fuel.
The original 3 main bearing engine built in 997cc, 1198cc, and 1339cc sizes were subsequently developed into 5 main bearing form in 1297cc and 1499cc sizes. They had reverse flow cylinder heads, that is the inlet and exhaust ports were all on one side. These engines had flat topped pistons with combustion chambers in the cylinder head. The crossflow design debuted in 1967 with the Heron type design.
The twin cam Lotus derivative was a development based on the larger 5 bearing engine, I woulg guess it too had flat top pistons in order to keep reciprocating mass as low as practicable in this high revving form.
For the benefit of other readers, I should clarify here that the Ford Kent/Valencia engine family had a long and convoluted history, having been developed in the late fifties for the Ford Anglia and other smaller English Fords. The three-bearing “Valencia” 957 cc and 1,117 cc engines that went into the initial Mk1 Fiesta were the second set of three-bearing versions, not simply a return to the original Anglia. Years later (after the run of the Mk2 Fiesta and beyond the scope of this article), Ford created a new five-bearing version of the three-bearing Valencia iteration, which I think saw its last bow in the Mk1 Ford Ka in the nineties. Its lineage is complicated enough to really beg for a flowchart!
Also 1996-1999 and 2000-02 Fiestas still offered the old 1.3 Kent/Valencia for selected markets (for example in Italy we only got it since late 1996 to 1998, other countries got it longer)
Would be very nice to have a complete history of this engine :)
I added a line about the five-bearing Valencia engine, although I think during the run of the Mk2 Fiesta that version was more often found in the European Escort. (Later, of course, it showed up in other models, notably the Mk1 Ford Ka.) The Valencia 1.3 is an odd duck: It was a five-bearing derivative of the scaled-down three-bearing adaptation of the five-bearing Kent, sharing the former’s smaller 74mm bore for reasons of production economy. It only existed because Ford Europe ended up needing more 1.3- and 1.4-liter engines than the now-defunct Bridgend plant could supply.
The Kent. Strangled by our first real anti pollutions regs here in Aus (ADR 27A, if you’re really that keen) A pig to work on in the Escort Mk 2, and a wheezy gutless slug. It took real genius to make an engine that was that simple, yet that hard to work on.
I owned a 1980 Fiesta S…. I have never loved a car more… performance upgrades…Avon 12 inchers for tires…. Dark blue…. it was one of those cars I never should have let go…..
Dear Aaron,
I love your entire website but seeing this article about my first car is magical. My father bought a red/black Fiesta Ghia Mk2 when I was 5 years old. I rode in it growing up and it then later became my first car. Against all better judgement, I still have it to this day. I rarely drive it now but when I do I’m smitten with its nimbleness and uncorrupted manual steering. It’s not fast by any means, but it’s quite a fun little car.
You mention it didn’t excel in any particular area but if I had to pick one, I’d say it’s a very well appointed car for its time and price bracket. As an example If you look under the dashboard you will find the bottom is fully carpeted, something many much newer and more expensive cars don’t feature.
Best regards, Rui
The Ghia models were quite plush for the B-segment, which was a savvy and prescient marketing decision — you didn’t have to pay for the extra trim if you didn’t want to, but if you did, Ford was happy to sell it to you. Of course, that was a lesson Lee Iacocca had learned years earlier and I have no doubt that Ford made a lot of money from it. (The price spread between the most basic Popular and the Ghia was sometimes as much as 30 percent!)
In 1980 (or so) I was living in North Dakota, just outside of Fargo. We lived in a housing development with a gravel road that had a terrible “washboarding” problem like many of them do. Late in the summer I noticed a Fiesta had started going by my house, usually at a pretty high rate of speed, driven by a fellow teenager who I hadn’t met yet. One day my dad had ridden up on his horse, and as I was talking to him in the yard there was suddenly a loud noise and a big cloud of dust across the empty field. Out of that cloud of dust came the Fiesta, tumbling end over end three or four times, coming to rest on its roof. My dad instantly galloped off to render assistance and I scrambled for my camera. By the time I got to the wrecked car in the ditch, neither my dad nor the driver was to be found. After the car came to a rest, my future friend Jeff unbuckled his seatbelt, fell to the roof, and climbed out the window. Finding himself mostly OK, he accepted my dad’s offer of a horse ride back to his house. Jeff later told me that while riding the tops of the washboards he turned a little and that was enough to make the car catch and start tumbling end over end. The car held up really well and I remember being amazed at that and taking a fair number of pictures. If I can dig them up I will post links to them. Not surprisingly, that’s not the only car Jeff has rolled and walked away from.
Another great article Aaron.
I worked as a mechanic in the ’80s, mostly keeping older cars on the road as rust and wear took its toll.
Ford had a generally well deserved reputation for being easy to fix, even though they were no more reliable or less rust prone than contemporary rivals. No doubt this helped them maintain good secondhand values, a significant factor in costing buying a new car.
The Fiesta was in very high demand as a used car in the UK, as you said it had few shortcomings, this and being easy and cheap to maintain no doubt helped, as did Fords reputation in the UK for making a range of practical and pleasant cars at the time.
Claud
I assume repair and maintenance costs were a factor in the success of the Fiesta and then particularly the FWD Escort, which became the darling of the British company/fleet car market in the ’80s. A lot of that market comes down to a pretty cold-blooded assessment of pence per mile and residuals.
Whatever one might think of Ford’s styling or engineering during that era, their merchandising acumen was really something else. They clearly understood their market extremely well and calculated very precisely how to minimize costs without having buyers feel shortchanged.
I worked as a mechanic at a small Ford dealership in the early 80’s and remember how much fun the Fiestas were to drive (and how not fun the early Escorts were!). Once we had two of them on the used line and one of the other wrenches and I raced them all over the lot and even in the shop one day when the boss wasn’t looking. Real Keystone Kops stuff.
Man, I wish I’d bought one.
I remember racing a co-worker around the parking lot of the Pizza joint that we worked at back in 1985.He had a Fiesta also.can you say “stupid teenage fun?” I know you could….
The fun ended when I smacked a curb head on.Dad,I need $…
Funny how the complaints about the CTX/CVT in the Fiesta are the same I have about the CVT in my Nissan Altima. Excellent for highway use, but the lack of response, the droning engine note(2.5 Nissan not noted for smoothness) and non linear response can be obnoxious to deal with.
My former wife owned a 1978 Fiesta when we married. It was a wonderful little car!
On the economic concerns, Ford (and others) then (as now) got round the challenge of amortizing initial tooling costs (heavy presses and dies for new shapes were always very expensive), by extending the production runs of these very cars, but of course it was necessary before investing to have confidence that the car would sell in reasonable volumes. I remember discussing the forthcoming Fiesta in (must have been about) early 1976 in relation to the recently introduced Renault 5, and being told that Ford welcomed the obvious success of the Renault because of the way it defined and expended a new class: maybe I read something in the motoring press along the same lines. No doubt it was partly a “party line” courtesy of the marketing department, but it was also, partly, fair comment.
The size of the investment was also increased by the “green field” plant decision, but of course in the longer term they no doubt calculated than a new plant in Valencia (using the lessons learned with the recently opened Saarlouis plant) could be operated more cost effectively than older facilities in Dagenham or Koeln-Niehle. And Ford do seem to have negotiated a very privileged status in Spain where for more than two decades Seat had been able to sell older designs by competition from modern designs from competitor manufacturers. The Spanish economy was still growing rapidly, but (in an age before most assembly was done by robots) industrial wages remained far lower than in England and Germany, and even if Franco was not universally loved in the country’s industrial regions, the industrial relations issues encountered in the UK during the 1960s/70s seemed unlikely to arise in the Valencia region. Even if future membership of the EEC for Spain was not a foregone conclusion, it did not take any particular insight to spot that Franco was quite old, and that his departure would most likely involve some sort of regime change…. So I do think the Valencia plant was an important component in the decision to go ahead with the Fiesta. (The 13 April 1977 issue of Auto Motor u Sport has an interesting half page on the Valencia plant and the government:Ford relationship background, if anyone can face the German language.)
Aside from the plant, I think Ford was also keen to get into a new market; they were concerned with the fact that their European business was very much concentrated in the north. Trying to compete directly with Peugeot, Renault, and Fiat with a new and unproven product IN France and Italy was going to be an uphill battle, but Spain was largely new territory.
My memories are of two Fiesta’s, both S models. The first was a rental in Brighton the summer of 1979 as my then-fiancee and I were over for the World Science Fiction Convention. I’d seriously looked at one that spring, but dad was loaning the money, and loans were only available for Chevrolet’s (dad was an ex-dealer). Absolutely loved that car on the B-roads between Brighton and Battle while Sally (who was completely indifferent to cars, considering them transportation appliances and nothing more) did the trip crouched down in the footwell. The thought of her beloved driving on the wrong side of the road for the first time, on the wrong side of the car, in his first front wheel drive car ever, AND attempting to learn how to four wheel drift it was a bit much for her.
My other memory of that car was the abysmal British assembly quality. A Hertz rental with a two-digit odometer when we picked it up, it was already rattling and sounding like it was going to fall apart. I can understand why we Americans got the German built cars.
Six years later, I finally got my own ‘S’, a used and repainted ’79. Had it for three years, fighting the rust monster every spring. It had an annoying vibration at 55mph which I fixed by never driving at that speed. Just take it up to 70 and everything was smooth.
Still think it was one of the finest basic cars ever made.
When I was 10 years old, we had a 78 base model and an 80 decor model. Both had been purchased new. Both yellow. At 10 years old, it was much less cool having 2 yellow Fiestas at the same time for your family vehicles. My dad commuted a half hour daily and ran the heck out of the cars and would brag about them at every chance. Being a gruff old-school guy from a different time, it was a big deal that he converted to the little cars. He said the 78 was notably faster than the 80 for some odd reason. After trading the 78 for an Escort :( the 80 went through two of my sisters and then on to me. I abused that 80 model being the car I really learned to drive with. I drove it stupid and hard and it had seen 4 wheels off the ground on a few occasions and it still never let me down. Even drove it a half hour home one morning with a broken belt (which ran the water pump also) and still hung in for the long haul. About 220000 miles without an engine rebuild, clutch, tranny, or any major deal-killing problems. I absolutely loved the car and actually turned down a brand new Festiva (from the Dad finance dept.) when I was in college after a minor accident. ABout 12 years ago, I finally purchased the car from California that I always wanted to build with dual weber side-drafts, roll cage, adjustable suspension, etc. I had purchased lowering springs on ebay and was negotiating some more parts when the guy said he hadn’t taken the car apart yet and it may be worth just buying the whole thing. When he sent me a picture of a yellow rust free car, I was in love.
Loved the article.
I currently own a 78 Ghia.You can check it out at Clunkbucket .com.It is my third and best Fiesta to date.It is so much fun that I cannot imagine trading it in for another modern boring car with no exhaust note,road feedback or character.I still surprise unsuspecting boring modern car drivers with the quickness and nimbleness of this car.They just don’t get it at all.Cheers to Ford for bringing this car to the USA! I feel like I’m 18 years old every time I get behind the wheel…..
I currently own a Black 1.3 MK2 fiesta Ghia.It was given to me years ago by a franchise owner in order to get me back on the job,.. his house.I love it.
Why? because it was given to me by a man I still think of as totally kool, it goes up Rownhams Hill and passes everything in sight, it has a cassette player which I could not live without and it encourages my neighbours to dent it at every given chance they get because they do not understand the concept and only see the weigh in value.
Whilst they are still at this price grab one quick then you will get it.
kk
I believe the rear wheel drive Cheetah project was canned when the Vauxhall Viva transmogrified into the Chevette, both ‘orrid little things. Ford could see the wisdom of NOT doing it that way.
We had an elderly Mk 1 Fiesta in Ireland. Boy did that motor rattle.
A fun little thing named Colleen.
My wife demanded a bigger car when she put her back out driving little Colleen down Mooncrater Street aka Douglas Rd in Cork!
Got an early Vectra.. Another story indeed.
The impression I got was that Ford gave up the RWD idea before the Chevette debuted, but I’d have to double-check the dates. The big issue from Ford’s perspective is that the money men dearly wanted RWD to cut tooling costs, but potential buyers turned up their noses at the Cheetah in every consumer clinic and marketing focus group Ford held on the matter. I don’t think any of the cars Ford showed were running prototypes, so it wasn’t a matter of dynamics but really of space. FR layouts are really bad for packaging efficiency in B-segment cars and I assume putting a RWD Cheetah mockup next to a Fiat 127, Peugeot 104, or Volkswagen Polo made that readily apparent.
Do any pictures exist of the RWD Cheetah project?
Also interested in finding more about the 1963 Ford World Car project, which apparently pre-dated the Bobcat project that eventually became the Fiesta.
Ford did not have any photos of it in their archives, but I think there may have been some in the more comprehensive development articles from around the Fiesta’s launch. (I don’t remember offhand if there are photos of the Cheetah in Edouard Seidler’s excellent book on the Fiesta.)
Another intriguing piece of backstory is Ford’s mooted collaboration with Toyota on what became the first Publica. I don’t think Ford had anything to do with the design of the Publica, but there were serious discussions with Toyota about joint production (this circa 1960–61). Eiji Toyoda’s book discusses that deal at some length.
I see, know that GM were working on similar small car projects such as the Vauxhall XP-714, Vauxhall S Car and Vauxhall Scamp projects (see Vauxpedia).
The only other small car project I am aware of which has a connection with Ford is a sporting version of the 4-wheeled Reliant Rebel called the Rebel 1600 GT, using a 80 hp 1.6 Ford Crossflow engine from the mk2 Ford Cortina 1600E.
Ford seemed to have a certain ambivalence about the whole thing: They kept returning to the idea every few years and then deciding it wasn’t worthwhile. Part of the disconnect, at least until the ’70s, was that many within Ford saw such a car primarily as a gesture toward what today would be termed “emerging markets” (such as Japan in the early ’60s or later India and other parts of South and East Asia) rather than a viable part of the mainstream European or American markets. The Anglia and Escort were already about as small as Ford figured their existing market would bear.
As far as the U.S. went, that was undoubtedly true. In the U.S. in the ’70s, a whole disparate mix of B-, C-, and D-segment sedans and hatchbacks were lumped together as “economy cars” in a way that would have raised the eyebrows of a contemporary buyer from most other markets.
Sure Ford justified their reluctance to develop a smaller car by how they costed a Mini and allegedly found it to be unprofitable (due to the former Morris personnel involved in properly costing cars being marginalized under BMC), yet there is some appeal in the idea of a 60s RWD sub-Anglia / sub-Escort hatchback car especially one fitted with a Twin-Cam or BDA engine and both Ford UK / Ford Germany must have worked on such projects prior to project Bobcat.
It is interesting to note regarding the 1963 Ford World Car project that it appeared roughly the same time as the larger Ford Cardinal project, which makes one wonder whether there is a connection between the two projects.
Going back to the Fiesta, the mk2 Fiesta spawned interesting less known variants from an uprated injected version of the Fiesta XR2 putting out around 115 hp and a turbocharged version of the Fiesta 1.6 XR2 by Turbo Technics putting out 125 hp, to an assortment of German tuning companies offering turbo kits for the 1.6 diesel engine with Suhe’s version putting out 85 hp.
The Cardinal project went back a good deal further and had a fairly torturous history; if anything, the later World Car project was perhaps a response to the Cardinal not materializing as intended, as in a sense was the Mk1 Escort.
As the article says, the general feeling at Ford was that they really didn’t need anything smaller and cheaper than the Escort. Looking at the dimensions and prices, you can sort of see why. It would have been difficult for Ford to produce something meaningfully cheaper than the Anglia, even if it had been smaller and completely conventional in engineering, and to the extent there was a market for something more economical to run, Ford didn’t think it was worth a big investment. It was certainly a lower priority than trying to finally align FoB and FoG.
I opted not to get into the aftermarket versions of the Mk1 and Mk2 Fiesta for the same reason I sort of glossed over the various factory special editions: just listing them all gets voluminous. The Fiesta certainly benefited from its commonality with the Mk3 and Mk4 Escort, which meant that any time some performance item was offered for the latter, someone would inevitably stick it on the Fiesta, whether Ford did or not.
The story of some postwar fwd prototypes “light car project” also have fallen into oblivion. It could be interesting to tell it (although there is enough informations). In the SIA’s article, a picture of a mockup with a transverly mounted engine was showed but it was the only one which I knew. However, on Deansgarage site, there is an interesting issue about Joe Oros, the ford’s designer. one photo looks like a styling proposal for this project (http://www.deansgarage.com/2016/joe-oros-ford-designer/). This car was like a mini with short front end and some tiny wheel.
I’m not sure which of those you’re looking at specifically, but most of them look to be concepts for late ’40s to mid ’50s standard Fords, plus a couple of Lincolns. A number of them appear to be scale models, which makes them look a bit more diminutive and toy-like than they actually were. That said, Joe Oros did have some involvement at the beginning of what became the Bobcat/Fiesta project.
As I understand it, the original development team had done some very crude mockups to illustrate the size and packaging — sort of the model equivalent of gesturing with your hands while saying, “And about this long…” However, the executives who saw the models had a hard time grasping that the mockups were not intended to represent what the car would actually look like, no matter how many times the development team said so. Finally, someone talked to Oros to get some help from styling in creating concept models that looked like real cars. Those designs weren’t intended for production and I don’t think they had any particular resemblance to the design studies done for the production car (which came later); they were mostly internal sales tools.
Certainly, you are right but they already had the idea for fwd small cars which eventually led towards the ford fiesta. Thank you
I wanted to point out the Oros44 picture.
Seems Ford of Germany in 1959 developed a rear-engined roughly Fiesta-sized project to compete with the Volkswagen Beetle and Renault Dauphine known as the Ford NPX-C5 that was to be powered by 34-40 hp 1.0-1.2 inline-4 engines and had a length of 146 inches (similar to 4-door SEAT 850, NSU Prinz 1000 and Simca 1000), the project was given the green light and dubbed the P4.
However Lee Iacocca disliked the car and felt it was too small for the US, which prompted him to launch the much larger front-engined fwd Ford Cardinal project that inherited the P4 codename and later became the German-built Ford Taunus P4/P6.
Thanks to the Facebook Group Car Design Archives for the above information.
Though it appears that costs prevented the NPX-C5 project from entering production in Germany, it is interesting to note that the NPX-C5 was smaller then a UK-built Ford Anglia and it’s 1.0-1.2 Inline-4 engine seems curiously similar to Ford UK’s Kent unit in terms of displacement even if there is no apparent connection between the engines.
I believe they’re conflating a number of pieces of a very complicated story, not all of them in the right order. To the best of my knowledge, the project you’re describing was developed about three years earlier than you mention and was part of a competitive design proposal process involving Dagenham, Dearborn, and Köln. The German FWD proposal was primarily the brainchild of August Momberger, formerly of Borgward, and probably inspired in large part by the Goliath GP. The Cardinal project was developed in Dearborn, not in Germany, and was essentially a follow-on to the earlier proposals, drawing bits and pieces from both of them with some new ideas intended to address their perceived limitations. It received development approval about five months before Iacocca became general manager of Ford Division, so while there were a lot of voices involved in three countries, I doubt Iacocca’s was one of them at that stage. (Iacocca was of course responsible for killing the U.S. version, but that was two years later, very soon before production began.)
The inline four, which was an OHC engine, was something quite different. I believe a V-4 was part of the FF package concept from the start (since the engine was to be set ahead of the transaxle, that seems likely). However, in the interim, Köln also came up with an alternative design with a more conventional FR layout; that’s what the I-4 was intended for. Since it had an overhead cam, I very much doubt it was related to the Anglia 105E engine other than being of roughly similar displacement.
Also for an 1.0-1.2 Inline-4 OHC engine it seems pretty underpowered compared to the Kent though probably a better alternative to the V4 assuming it was capable of being enlarged along similar lines to the Kent and V4 engines.
Since the inline engine never came near production, I don’t know how much power it would actually have had. Again, I suspect the group you mention is conflating several sets of facts, so I don’t know how much stock to put in the 34–40 hp figure. The early three-bearing Anglia 105E engine had 41 hp from 997 cc and I can’t see an OHC four of the same displacement being less powerful than that, although I don’t suppose it would have had any more torque. (The Kent got a lot of massaging over the years, driven by the need to use bigger versions of it in the Cortina.)
From what I have been able to look up from reading up the translated German language links shown in the group. The rear-engined NPX-C5 was a separate project by Ford of Germany intended for Europe, while the Cardinal was developed in the US for both domestic and German markets yet later pushed on Ford of Germany.
Interested to know what Dagenham’s contribution was in the competitive design proposal process.
What intrigues me is that many an enthusiast has always assumed that Ford of Germany’s only small engine option was the dreadful V4 engine in the Cardinal aka Taunus P4, whereas the NPX-C5’s OHC unit suggests that there were other options available had the green light been given as an alternative to the V4 unit for either the Taunus P4 or NPX-C5.
The only other German company around that period that developed a similar small OHC engine with valve gear driven using a toothed rubber cam-belt,was Glas via the Glas 1004.
The V-4 was deemed essential to the FWD package for packaging reasons. At that point, to fit an inline-four within the requisite exterior dimensions would have meant setting it transversely and probably using a chain to drive the transaxle, which was something Ford engineers considered and were not happy about. My understanding is that the V-4 was designed with a “compactness uber alles” mindset, although they had to compromise somewhat to get it to work at all.
Ebay seems to be selling that particular issue you are after.
Somewhat OT though it is curious that Ford of Germany never produced a direct pre-Escort equivalent to Ford UK’s Anglia, unless NPX-C5 was conceived as such or there was somehow an as yet unknown smaller Taunus P4-based project with a destroked 1000cc V4.
It is surprising that the German market went for the more middle-class offerings first — one would ordinarily expect (for instance) the Opel Kadett to have come before the Rekord rather than the other way around.
Fair Enough.
Seems that Opel (along with Vauxhall initially as separate projects) only recognized the need for a smaller car by the late-1950s, with the Opel Kadett A originally known provisionally as the Opel 700.
Guess the unexpected success of the Volkswagen Beetle by the early/mid-1950s had many companies scrambling for an answer, kind of wished the US’s Big Three joined the mix with their unconventional proposals (GM / Vauxhall’s XP-714, Ford’s NPX-C5 and whatever equivalent Chrysler US was cooking up at the time).
I am guessing so far as Opel and Ford-Werke are concerned, it reflected their assessment of the state of the German economy and whether there were enough buyers who could afford something Kadett/Escort-sized who couldn’t just buy the bigger cars. The Japanese market followed a similar trajectory; the Datsun Bluebird and Toyopet Corona preceded the Sunny and Corolla by quite a few years, although there were the early kei-cars, which one could (very loosely) compare to the German “bubble-cars” of the late ’50s.
Okay, on further investigation, it appears the group post you saw is based on a German article in auto.de from last August, which has photos of the prototype. Several points are obvious factual errors: again, Lee Iacocca was not president of Ford, nor even general manager of Ford Division, in February 1960. The two photos described as NPX-C5 don’t appear to be the same model. The first photo looks like an early full-size model of the Cardinal (the greenhouse is close to the production 12M, but the grille is a different shape) while the second is a quite different two-box design. As for the engine specifications, I remain skeptical because even the 1.2-liter engine in the late ’50s Taunus 12M — which was an undersquare L-head design — managed 43 hp by 1957.
Again, I think what’s likely happened is that someone has conflated details about several distinct developments and reassembled them in the wrong order. The car Köln wanted to build at the time the article describes was FR, not RR, although it seems perfectly reasonable that Ford-Werke would have at least contemplated a RR car in this period. Interestingly, the belt-driven OHC design the Germans came up with was not inspired by Glas — it actually preceded the 1004, at least the production iteration, by more than two years.
I see, thanks for investigating further.
It brings up the question of how one explains existence of Ford’s rear-engined two-box design that appears to precede the Volkswagen Type 4 from the rear?
Aware the NPX-C5’s belt-driven OHC engine preceded the Glas 1004 design by a few years, just that the motor industry tends to be a small world where a design (be it an engine or car) rejected by one company is subsequently accepted upon engineers involved moving to another company.
Though the following is baseless speculation on my part. It might have possibly been the case that the 1.0-1.2-litre NPX-C5 OHC engine’s claimed power output of 34-40 hp was actually confused with the V4 unit.
That is if one assumes the V4 was originally conceived as a 34 hp 1-litre engine (of around 992-999cc) for Ford Germany’s original “Anglia-sized” NPX-C5 small car project, prior to growing in size and being fitted with enlarged 40-55 hp 1183-1498cc V4 units for the Cardinal / Taunus P4 (until US production was canned).
To be perfectly honest, I’m not sure how much of the information in that article is at all reliable. I haven’t found any other references to an NPX-C5 project other than the autos.de article and the Facebook group that refers to it, and none of the information I have on the Cardinal’s development (I did find that SIA article, which is by Karl Ludvigsen) mentions a RR program. The article contains several clear factual errors, mislabels one of its two photos, and leaves me uncertain about the provenance of the other (although it is pretty clearly a two-box RR model). Ford-Werke had previously proposed a FF car, circa 1956–1957, which was not the Cardinal project but an unbuilt precursor to it; it seems reasonable to me that they would have at least contemplated an RR model, but I haven’t found any specific indication to that effect. The model Köln proposed as an alternative to what became the P4 12M/15M was a FR design, not a RR one.
As for the engine, I can only take the article’s quoted power outputs with a sizable grain of salt. The 1,172cc inline-four in the late ’50s Taunus 12M had 43 hp by 1957; why would Köln propose investing a substantial amount of money in an all-new OHC engine that was no more powerful than the existing, rather elderly undersquare L-head engine? That doesn’t seem like a terribly prudent investment.
The V-4 development was, according to Ludvigsen, in two directions. The initial conception was for a 1.1-1 or 1.4-liter 20-degree engine, very Lancia-like, development of which continued for a time in parallel to the now-familiar 60-degree type. Since the narrow-angle engine was canceled in the spring of 1960 due to too many unanswered engineering questions and a lot of balance issues, any reports of its output are either not representative (the output of a troublesome, cobbled-together prototype is not fairly comparable to a production engine) or really speculative.
Again, the idea that there was a RR project seems reasonable, but I’d have to get in touch with Ford Archives to see if they have anything more substantive.
You have a point regarding the 1.0-1.2 OHC engine.
Shame the initial 1.1/1.4 20-degree V4 design never worked out, makes me wonder whether the related Cologne V6 was in turn also originally intended to be a narrow-angle design roughly similar to BMC’s own shelved more sophisticated narrow-angle V4/V6 engine project.
Thanks again for looking further into this subject.
Nope, the Cologne V-6 was conceived along with the 60-degree V-4. In fact, that was one of the reasons Ford decided the 60-degree engine was more viable: The development team said, “Hey, you know, we could make a decent 60-degree V-6 out of this pretty easily.” So, while the V-6 didn’t appear until several years after the V-4, the idea was on the table almost from the start. (Of course, you can also make a narrow-angle V-6, as Volkswagen reminded everyone in the ’90s, but a 60-degree bank angle makes it quite straightforward.)
Guys, don’t forget the horrific Essex V4 used in the Corsair and the Transit :)
Yup — as I understand it, the Essex family was originally conceived for the Mk1 Transit, which was the first real Dagenham-Köln joint development project. I don’t know offhand when the idea of making a V-6 of it to replace the I-6 in the Zephyr and Zodiac came into the picture, although given the timing, I assume that at the latest, it was around the time the Transit debuted.
Where would the British kit car industry have been without the 3-liter Essex, though?
I was working at a Ford dealer in Reading UK when the first Fiesta was delivered. In comparison to what we had been working on it looked like something other worldly :) A colleague noted that the driveline looked very Fiat like. But once the guys worked out that they could spin the gearbox around to do a clutch without removing the driveshaft’s, meaning they could do the job way quicker and therefore earn more money. The Fiesta soon became the norm.
A curious thing about the mk1/mk2 Ford Fiesta is the fact they were only available as a 3-door hatchback.
Turns out Ford looked at 2/4-door saloon variants, the European version looking rather attractive and suggesting there was potential for a Fiesta 5-door hatchback bodystyle.
https://driventowrite.com/2017/01/24/ford-fiesta-development-story-part-1/
Not that many UK kit cars used the Ford V6 engine;far more were built using the lightweight(by the standards of the day)I4 Kent engine, and plenty of power was simple to obtain therefrom.The V6 found a home in the limited production Reliant Scimitar family, the Marcos, and the Gilbern.
The line between “kit car” and “limited production model” is of course a narrow one, particularly with cars like the Gilbern that you could buy in kit form as a purchase tax dodge. (Scimitar fans might object to that characterization, I suppose.)
Lotus, Marcos, Gilbern were sold for home assembly as complete sets of parts, really CKD cars, until the Purchase Tax laws were changed. Professional assembly was not allowed , otherwise the tax became due,
but that didnt stop some smaller garage, on the quiet, putting the cars together for the mechanically inept.
In the UK, a kit car is one in which the builder buys a kit, usually a bodyshell, a chassis, maybe the suspension, and the drivetrain mountings,and separately obtains the other parts from one or more donor vehicles.
Yes, I’d learned that when I looked into Gilbern for the sidebar on shooting brakes in the Volvo P1800 article. It’s one of those details that’s really crucial to understanding the development of the “kit car” market in the U.K., especially when one considers that purchase tax could be 40% or more of the purchase price!
Really a great article, congratulations!
In my family there have been two older Fiestas, both bought well used; my mother had a 1986 Mk2 1.6 diesel Ghia from 1997 (paid very little) to 2000 and my brother had a 1991 1.1 SX 3-doors as his first car since 2001 to 2003. They were very good and dependable cars, ai feed very easy and simple to work on.
A little note, side repeaters were added in 1986 for UK (because I believe they became mandated that year there) but they were already adopted since the beginning of the Mk1 for Italian market because compulsory since many years.