RX-Rated: Mazda’s Early Rotary Cars, Part 2

2007 Mazda RX-8 40th Anniv and 1967 Cosmo front 3q press - copyright 2007 Mazda
A 40th Anniversary Edition RX-8 poses with a 1967 Mazda Cosmo Sport. The white L10A is the same Cosmo Sport seen in part one of this story; it was originally owned by Curtiss-Wright and was acquired by Mazda in 2007. (Photo circa 2007; copyright and courtesy Mazda)

Considering the rotary’s ups and downs in the marketplace, that perseverance may seem quixotic, but Mazda has remained committed to the rotary engine for far longer than even NSU, which pioneered the design with inventor Felix Wankel in the 1950s. While poor fuel economy ultimately limited the Mazda rotary engine’s impact on the family sedan market, the company nonetheless managed to sell a million rotary-powered vehicles from 1967 to January 1978. The first-generation RX-7 would account for another 500,000 units between 1978 and 1985.

Moreover, Mazda succeeded in making the rotary a viable production engine, where even Daimler-Benz and General Motors had given up. That’s quite an accomplishment for a small automaker and it’s a fine legacy for Kenichi Yamamoto and the late Tsuneji Matsuda, who decided back in 1960 that the rotary engine would become his company’s signature. Fifty years later, it still is.

# # #

AUTHOR NOTE AND ACKNOWLEDGMENTS

The author would like to thank Johnny Aguirre, Alain Durand, ‘verner_oscar,’ and ‘Telkine’ for the use of their photos; Halie Schmidt of Hill & Knowlton, Mazda’s PR agency, for her assistance in obtaining images and information from Mazda’s archives (some of which were provided on a nifty flash drive shaped like a trochoidal rotor); and Bob Nichols for the generous loan of his camera to take some of the author photos in this article.

The title of this article was inspired by the tagline of a mid-nineties U.S.-market Mazda ad, although the original ad was for the Miata, not a rotary-engined car.

For the record, the author has never owned a Mazda rotary, but does own a Mazda3 sedan, and years ago was compensated by a marketing firm hired by Mazda for participating in a couple of owner focus groups related to that model.


NOTES ON SOURCES

Information on the development and history of the rotary engine and Mazda’s rotary-powered cars came from “1969-1972 Mazda Luce R130: Putting Mazda on the Map” (10 September 2010, Autopolis, autopolis.wordpress. com/ 2010/09/10/ 1969-1972-mazda-luce-r130-putting-mazda-on-the-map/, accessed 7 October 2011); “A Dozen Small Wagons,” Road & Track Vol. 25, No. 2 (October 1973), pp. 38-49; Mike Ancas, Mazda RX-7 Performance Handbook (Motorbooks Workshop) (Osceola, WI: Motorbooks International, 2001); R.F. Ansdale, “Wankel Progress,” Motor Trend Vol. 18, No. 2 (February 1966), pp. 29-31; Arban’s Mazda site, n.d., home.online. no/~arban/, last accessed 19 October 2011; Tony Assenza, “Can the Rotary Engine Survive the ’80s?” Popular Mechanics Vol. 154, No. 4 (October 1980), pp. 83-85, 206; Patrick Bedard, “The Karma of the Kosmo,” Car and Driver Vol. 38, No. 12 (June 1993), pp. 103-109; Ryan Beene, “Mazda halts production of the RX-8 rotary-engine sports car,” Autoweek 22 August 2011, www.autoweek. com, accessed 12 October 2012; Bernard, “Rotary Rocket: 1972 Mazda RX-2 Coupe!” (21 May 2009, California Classix, www.californiaclassix. com/ Bernard/ RX-2-1.html, accessed 9 October 2011); “Brief Test: Mazda RX-2 Automatic,” Road & Track Vol. 24, No. 6 (February 1973), pp. 57-58; Mike Covello, Standard Catalog of Imported Cars 1946-2002, Second Edition (Iola, WI: Krause Publications, 2001); Craig’s Rotary Page, cp_www.tripod. com/ rotary/ index.htm, last accessed 25 October 2011; Per Danny, “My 1969 Mazda Cosmo Sport (L10B)” (6 January 2010, Australian Mazda Owners Car Club/Forum, www.ozmazda. com/ board/ index.php/ topic/ 11304-my-1969-mazda-cosmo-sport-l10b/, accessed 6 October 2011); Connie Goudinoff Downing, “The Little Engine That Did” (1992, MazdaSpeed Motorsports, www.mazdausa.com, accessed 1 November 2011); Jim Dunne, “Chevy’s new Vega-size, Wankel-powered car,” Popular Science Vol. 204, No. 4 (April 1974), p. 84-86, 172; Jim Dunne and Ray Hill, “Capsule Test: Mazda Cosmo,” Popular Science Vol. 208, No. 3 (March 1976), p. 50; Kelvin Fu, Aaron J. Knobloch, Fabian C. Martinez, David C. Walther, Carlos Fernandez-Pello, Al P. Pisano, Dorian Liepmann, Kenji Miyasaka, and Kaoru Maruta, “Design and Experimental Results of Small-Scale Rotary Engines,” Proceedings of 2011 ASME International Mechanical Engineering Congress and Exposition (IMECE2001/MEMS-23924), November 2001; Carl Grothmann, “First Driving Report: Japanese Wankel-Powered Car,” Popular Science Vol. 190, No. 4 (April 1967), pp. 81–84; Hans Greimel, “Mazda’s rotary engine stalled, not forgotten,” Autoweek 20 October 2010, www.autoweek. com, accessed 12 October 2011; Bill Hartford, “Mazda RX-4: What, no altimeter?” Popular Mechanics Vol. 142, No. 2 (July 1974), pp. 96, 162, and “Speed and the Single Rotor,” Popular Mechanics Vol. 147, No. 3 (March 1977), p. 198; John B. Hege, The Wankel Rotary Engine: A History (Jefferson, NC: McFarland & Company, Inc., 2001); Takeo Hoshi and Anil Kashyap, “Chapter 5.2: Toyo Kogyo (Mazda) and Sumitomo Bank,” Corporate Financing and Governance in Japan: The Road to the Future (Cambridge, MA: Massachusetts Institute of Technology, 2001), pp. 153-158; HoTWire, “Rare Car: Mazda R130,” Retro Scene Mag 4 September 2008, retroscenemag. com/ post/ Rare-Car-Mazda-R180.aspx, accessed 7 October 2011; Hiroshi Inoue, [“Giugiaro-Design Mazda S8P (First-Generation Luce Prototype)”], 11 October 2012, indexindex. jp/?paged=3/, accessed 23 September 2015; “Is the Wankel the auto engine of the future?” Changing Times: The Kiplinger Magazine Vol. 26, No. 7 (July 1972), pp. 43-48; Wanda James, “Chapter 10: Mazda Makes Its Mark,” Driving From Japan: Japanese Cars in America (Jefferson, NC: McFarland & Company, Inc., Publishers, 2007); “Japanese Car Production: Mazda” (no date, Unique Cars and Parts, www.uniquecarsandparts. com.au, accessed 3 November 2011); Dale Jewett, “Mazda marks end of RX-8 production with Spirit R edition in Japan,” Autoweek 7 October 2011, www.autoweek. com, accessed 12 October 2011; Edwin Krampitz, Jr., “Mazda 16X Rotor Dimensions and Technical Details” (22 September 2009, RotaryNews.com, rotarynews. com/ node/ view/ 1050, accessed 12 October 2011); Mike Knepper, “The Meyers Mazda,” Road & Track Vol. 25, No. 3 (November 1973), pp. 36-38; Michael Lamm, “PM Owners Report: Mazda RX-2 and RX-3: Enthralled by performance, appalled by mileage” and “Taking the mystery out of miles per gallon,” Popular Mechanics Vol. 142, No. 2 (July 1974), pp. 97-101, 162; L’Editrice Dell’Automobile LEA, World Cars 1971 (Bronxville, NY: Herald Books, 1971), World Cars 1973 (Bronxville, NY: Herald Books, 1973), World Cars 1979 (Pelham, NY: Herald Books, 1979), and World Cars 1985 (Pelham, NY: Herald Books, 1985); Jay Leno, “Mazda Cosmo Sport 110S: An Under-Appreciated Classic,” Popular Mechanics October 2009, www.popularmechanics. com/ cars/ jay-leno/ 2629006, accessed 7 October 2011; Arvid Linde, Preston Tucker & Others: Tales of Brilliant Automotive Innovators & Innovations (Dorchester: Veloce Publishing Ltd., 2011), pp. 48-52; E.F. Lindsley, “How they improved the Mazda mileage,” Popular Science Vol. 208, No. 3 (March 1976), pp. 52, 130, and “The rotary is not dead,” Popular Science, Vol. 213, No. 3 (September 1978), pp. 78- 81; Brian Long, RX-7: Mazda’s Rotary Engine Sports Car (Revised 2nd Edition) (Dorchester: Veloce Publishing Ltd., 2004); Karl Ludvigsen, “How Big Are Wankel Engines?” Hemmings Sports & Exotic Car #32 (April 2008); Peter Lyon, “Driving the Mazda Cosmo Sport: Legendary Rotary-Powered Coupe Tugs at the Heart-Strings, 40 Years On” (24 December 2010, Motor Trend, www.motortrend. com/ roadtests/ coupes/ 1012_driving_the_mazda_cosmo_sport/, accessed 9 October 2011); Madaz, “My Mazda Luce Rotary Coupe” (27 November 2007, Japanese Nostalgic Car, japanesenostalgiccar. com/ forum/ viewtopic.php?t=812, accessed 17 October 2011); Wesley Mahler, “How a Rotary Engine Works” (25-26 November 2005, Rotary Engine Illustrated, www.rotaryengine illustrated.com/ how-a-wankel-rotary-engine-works/ index.php, accessed 13 October 2011) and “Rotary Engine Porting” (15 October 2006, Rotary Engine Illustrated, www.rotaryengine illustrated.com/ porting/ peripheral-port-14.html, accessed 13 October 2011); Frank Markus, “1970 Mazda Cosmo Sport 110S: Driving Mazda’s Original ‘Hum-m-m-m-er'” (23 August 2007, Motor Trend Blog, blogs. motortrend.com/ 1970-mazda-cosmo-sport- 110s-1017.html, accessed 12 October 2011); Nate Martinez, “Mazda’s 10 Most Significant Rides” (20 May 2010, Motor Trend, www.motortrend. com/features/consumer/ 1005_mazda_10_most_significant_rides/viewall.html, accessed 19 October 2011); John Matras, Mazda RX-7 (Sports Car Color History) (Osceola, WI: MBI Publishing Company, 1994); “Mazda Heritage” (no date, Unique Cars and Parts, www.uniquecarsandparts. com.au, accessed 3 November 2011); “Mazda Magic: Fastback 2-plus-2 from Japan – with Wankel Power,” Hot Car Magazine February 1970, pp. 37-39; Mazda Motor Corporation, “Great Cars of Mazda” (no date, www.mazda.com, last accessed 25 October 2011), “History of Mazda” (no date, www.mazda. com, last accessed 17 October 2011), “Mazda Spirit: The Rotary Engine” (13 August 2007, www.mazda. com, last accessed 20 October 2011), and “Next Generation RENESIS (Rotary Engine 16X) (no date, www.mazda. com, accessed 12 October 2011); “Mazda Luce Rotary Coupe RX-4,” Old Cars of Japan ’70, 17 May 2011, ah5243.blog72.fc2. com/blog-entry-92.html?sp, accessed 22 September 2015; “Mazda Motorsports Milestones” [Mazda USA press release], 2004; “Mazda Museum” (no date, CorkSport Mazda Performance, www.corksport. com/ mazda-museum.html? currency=cad&sl=EN, accessed 9 October 2011); Mazda Performance Corner, “Racing Heritage: A Conversation with Connie” (no date, Mazdaspeed Motorsports, www.mazdausa. com, accessed 1 November 2011); “Mazda Roadpacer” (no date, Unique Cars and Parts, www.uniquecarsandparts. com.au, accessed 3 November 2011); “Mazda Rotary Pickup: A revolutionary concept!” Road & Track Vol. 25, No. 11 (July 1974); “Mazda Rx-2” (30 August 2009, African Muscle Cars, www.africanmusclecars. com/ forum/ viewtopic.php?f=39 &t=3350, accessed 9 October 2011); “Mazda RX-2,” Road & Track Vol. 22, No. 9 (May 1971), pp. 78-81; “Mazda RX3” (no date, Unique Cars and Parts, www.uniquecarsandparts. com.au, accessed 3 November 2011); David Morris, “Eunos Cosmo History” (no date, DMRH Special Vehicles, www.dmrh. com.au/ jchistory1.htm, accessed 16 October 2011), “Mazda R100 History from Down-Under” (no date, Mazda Rotary Club, mazdarotaryclub. com/ mazda_history/ mazda_r100_history/ mazda_r100_history.htm, accessed 7 October 2011), “The Quiet Achiever” (no date, DMRH Special Vehicles, www.dmrh. com.au/ hb_series2.htm, accessed 16 October 2011); “MrMazda” and “superrob” (21 February to 3 March 2011, Mazda Owners Club SA, www.mazdaownersclub. co.za/ viewtopic.php?f=2&t=6367, accessed 9 October 2011); Troy Nassar, “Chrysler South Africa in the 1970s” (no date, Allpar.com, www.allpar.com/ world/ south-africa.html, accessed 9 October 2011); “New Japanese Wankel?” Popular Science Vol. 195, No. 3 (September 1969), p. 118; Karim Nice, “How Rotary Engines Work” (29 March 2001, HowStuffWorks.com, auto.howstuffworks. com/ rotary-engine.htm, accessed 13 October 2011); Masami Nishimoto and Kenichi Yamamoto, “Winds of Change at Mazda: The Story of Half a Century,” Installments I and II, The Chugoku Shinbun, 22-23 January 1998; Jan P. Norbye, “Mazda RX2: 18 Months and 30,000 Miles on a Wankel,” Popular Science Vol. 202, No. 5 (May 1973), pp. 84-85, and “The View Down the Road,” Popular Science Vol. 201, No. 3 (September 1972), pp. 44-45, and The Wankel Engine: Design, Development, Applications, 2nd printing (Philadelphia: Chilton Book Company, 1972); Jan P. Norbye and Jim Dunne, Popular Science Vol. 201, No. 2 (August 1972), pp. 36-46; Jan P. Norbye, Jim Dunne, and Jim Davis, “PS Puts 10,000 Miles on the New Mazda: Wankel-Powered Car Proves Silent, Powerful, and Trouble-Free,” Popular Science Vol. 200, No. 1 (January 1972), pp. 83-85; Masako Osada, Sanctions and Honorary Whites: Diplomatic Policies and Economic Realities in Relations Between Japan and South Africa (Westport, CT: Greenwood Press, 2002); Minoru Ota, “The Maedas’ Touch” Zoom Zoom Magazine, Summer 2008, www.mazdausa. com, accessed 13 October 2011; Alexander Palevsky and Jay Lamm, “God of RX-7,” Sports Car International, August-September 1998 (Vol. 14, No. V); Richard Pascale and Thomas P. Rohlen, “The Mazda Turnaround,” Journal of Japanese Studies Vol. 9, No. 2 (Summer 1983), pp. 213-263; Tim Pollard, “CAR interviews Mazda design chief Ikuo Maeda (2010),” CAR 2 September 2010, www.carmagazine. co.uk, accessed 13 October 2011; Laurence Pomeroy, “Laurence Pomeroy Probes Engine Development,” Motor Trend Vol. 18, No. 2 (February 1966), pp. 22-25; “RX-2” (no date, Mazda Rotary, www.mazdarotary. net/ mazda_rx2.htm, accessed 9 October 2011); Aaron Robinson, “A Tale of Two Rotaries,” Car and Driver September 2007, www.caranddriver.com/ news/ car/ 07q3/ a_tale_of_two_rotaries-car_news, accessed 15 October 2011; “rotaRRacing,” “Mazda CD Cosmo / Rx-5 History Worldwide” (22 November 2006, AusRotary.com, www.ausrotary. com/ viewtopic.php? f=3&t=118253, accessed 16 October 2011); “rotaryking,” “R130 Luce – 13A Rotary Goodness” (9 October 2011, AusRotary.com, www.ausrotary. com/ viewtopic.php? f=31&t=153800, accessed 28 October 2011); David Scott, “Has Japan Grabbed the Lead in Wankel-Powered Cars?” Popular Science Vol. 192, No. 4 (April 1968), pp. 75-77; Douglas Self, “Rotary Steam Engines” (27 October 2009, The Museum of Retro Technology, www.aqpl43.dsl. pipex.com/ MUSEUM/ POWER/ rotaryengines/ rotaryeng.htm, accessed 7 October 2011) and “Rotary Internal-Combustion Engines” (19 October 2009, The Museum of Retro Technology, www.aqpl43.dsl. pipex.com/MUSEUM/POWER/ unusualICeng/ rotaryIC/ rotaryIC.htm, accessed 7 October 2011); Don Sherman, “Mazda Cosmo,” Car and Driver Vol. 21, No. 8 (February 1976), pp. 60-64, 82; Steve Smith, “1972 Mazda RX-2: With or Without Rotary Power, This Car is Ergonomic Perfection,” Motor Trend Vol. 24, No. 11 (November 1972), www.motortrend. com/ classic/ roadtests/ 7211_1972_mazda_rx_2/ viewall.html, accessed 9 October 2011; “Specifications: 1974 Imported Cars,” Car and Driver Vol. 19, No. 5 (November 1973), pp. 93-95; “Super Coupe Comparison Test,” Car and Driver Vol. 16, No. 6 (December 1971), pp. 25–32, 68–70; “Superrob” (12 January 2011, Mazda Owners Club SA, www.mazdaownersclub. co.za/ viewtopic.php? f=2&t=6128, accessed 9 October 2011); “The new Mazda — checking it out on the road,” Changing Times: The Kiplinger Magazine Vol. 26, No. 6 (June 1973), pp. 11-13; “The Series….1.. 2.. 3.. 4.. Rx2… Capella 616” (no date, home.alphalink.com. au/ ~hillsk/ capella1.htm, accessed 9 October 2011); Andrew Tobias, “The Mazda Drives East,” New York Vol. 5, No. 48 (27 November 1972), pp. 66-69; Charles Trieu, “1973 Mazda RX 3 – Rotary Experiment,” Super Street February 2010, www.superstreetonline. com, accessed 10 October 2011; Mark Warner, Street Rotary: How to Build Maximum Horsepower & Reliability into Mazdas (New York: HPBooks, 2009); Larry Webster, “How It Works: The Mazda Rotary Engine (With Video!)” Popular Mechanics September 2011, www.popularmechanics. com/ cars/ news/ fuel-economy/ how-it-works-the-mazda-rotary-engine- with-video, accessed 7 October 2011; J. Patrick Wright, On a Clear Day You Can See General Motors: John Z. DeLorean’s Look Inside the Automotive Giant (Chicago, IL: Avon Books, 1980); Wally Wyss, “Mazda Wankel vs. Comet 302,” Motor Trend Vol. 23, No. 5 (May 1971), pp. 76-78, 87; and an email to the author from Ben Hsu of Japanese Performance Cars, 28 October 2011.

Additional information on Mazda’s rotary competition efforts came from “Bathurst 1971: Hardie-Ferodo 500,” “Bathurst 1972: Hardie-Ferodo 500,” “Bathurst 1973: Hardie-Ferodo 1000,” “Bathurst 1974: Hardie-Ferodo 1000,” “Bathurst 1975: Hardie-Ferodo 1000,” and “Bathurst 1976: Hardie-Ferodo 1000” (no date, Unique Cars and Parts, www.uniquecarsandparts. com.au, accessed 7 November 2011); Patrick Bedard, “Rotary Racer and Piston Politics,” Car and Driver Vol. 19, No. 10 (April 1974), pp. 58-74; Jim Donnelly, “Baby, It’s You: IMSA RS, the Ellis Island of Japanese-branded sedan racing,” Hemmings Sports & Exotic Car #56 (April 2010); “Former Hunterdon resident Walt Bohren, Mazda car racer for many years, drowns in British Virgin Islands,” Hunterdon County Democrat 10 February 2011, www.nj. com, accessed 13 October 2011; Michael J. Fuller, “An Interview with Jim Downing,” conducted 20 January 1996 (2000, www.mulsannescorner. com/ downing.htm, accessed 12 October 2011); Alexis Gosseau, “IMSA RS Challenge : everybody could go racing” (25 October 2009, IMSAblog, alex62.typepad. com/ imsablog/ 2009/ 10/ imsa-rs-challenge-everybody-could-go- racing.html, accessed 10 October 2011); Berny Herrera, “Rotary Power Shines at the 2006 SCCA Solo National Championships” (4 October 2006, RotaryNews.com, rotarynews. com/node/view/844, accessed 12 October 2011); Jeff Koch, “Le Mans-winning Mazda 787B to appear at the Japanese Classic Car Show” (24 August 2011, Hemmings Blog, blog.hemmings. com/index.php/2011/ 08/24/ le-mans-winning-mazda-787b-to-appear-at-the- japanese-classic-car-show/, accessed 13 October 2011); Aaron Robinson, “Checkered Past,” Car and Driver April 2007, www.caranddriver. com, accessed 15 October 2011; Chris Rosamond, “Epic Mazda 787B Rides Again: 700hp rotary racer to return for Le Mans demo” (23 May 2011, PistonHeads, www.pistonheads.com/news/default.asp?storyId=23665, accessed 13 October 2011); “Second Crop of Classes Halfway to a Solo National Championship” (27 September 2007, SCCA, 216.58.238.210/ newsarticle.aspx? hub=3&news=3163, accessed 12 October 2011); and Brock Yates, “The New Little Engine That Couldn’t,” Sports Illustrated 16 April 1973, pp. 79-81, sportsillustrated.cnn. com, accessed 19 October 2011.

Additional information on the environmental legislation of the 1970s and the 1973 OPEC embargo came from Chris Bishop, ed., The Encyclopedia of 20th Century Air Warfare (London: Amber Books/Barnes & Noble, 2004); California Environmental Protection Agency Air Resources Board, “Key Events in the History of Air Quality in California” (13 January 2011, ARB, www.arb.ca. gov/ html/brochure/ history.htm, accessed 18 October 2011); Anthony Curtis, “Is cleanliness three-cornered?” New Scientist and Science Journal Vol. 49, No. 740 (25 February 1971), pp. 415-417; Environmental Protection Agency, “Milestones” (9 July 2007, EPA, www.epa. gov/ oms/ invntory/ overview/solutions/ milestones.htm, accessed 10 October 2011); David Halberstam, The Reckoning (New York: William Morrow and Company, 1986); Michio Hashimoto, “History of Air Pollution Control in Japan,” How to Conquer Air Pollution: A Japanese Experience (Studies in Environmental Science 38), ed. Hajime Nishimura (Amsterdam: Elsevier Science Publishers B.V., 1989), pp. 1–90; David C. Isby, Jane’s Air War I: Fighter Combat in the Jet Age (New York: Collins Reference, 1997); National Traffic Safety and Environmental Laboratory, “Overview and Future Prospect of Emissions Regulations in Japan” (4 February 2003, NTSEL, www.ntsel. go.jp/e/ symposium/040203session4.pdf, accessed 10 October 2011); Donald Neff, Warriors Against Israel: How Israel Won the Battle to Become America’s Ally 1973 (Ft. Collins, CO: Linden Press, 1981); Hajime Nishimura and Masayoshi Sadakata, “Emission Control Technology,” How to Conquer Air Pollution: A Japanese Experience, pp. 115–115; the official website of the Organization of the Petroleum Exporting Countries, www.opec. org, accessed 14 November 2011; and the Wikipedia® entries on the 1973 oil crisis (en.wikipedia.org/wiki/1973_oil_crisis, accessed 13 October 2011) and the Yom Kippur War (en.wikipedia.org/wiki/Yom_Kippur_War, accessed 14 November 2011).

Additional information came from the Auto Editors of Consumer Guide, “1963-1966 NSU Wankel Spider” (24 July 2007, HowStuffWorks.com, www.howstuffworks. com/ 1963-1966-nsu-wankel-spider.htm, accessed 7 October 2011); International Money Fund, “Cooperation and reconstruction (1944–1971)” and “The end of the Bretton Woods System (1972–1981),” About the IMF: History, N.d., www.imf.org/external/about/history.htm, last accessed 2 April 2014; Jim Kaler, “Capella” (13 December 1998, University of Illinois Department of Astronomy, stars.astro. illinois.edu/ sow/ capella.html, accessed 13 October 2011); “Kohei Matsuda, Former President of Mazda,” New York Times 4 August 2002, www.nytimes. com, accessed 14 November 2011; Jona Lendering, “Ahuramazda and Zoroastrianism” (no date, www.livius. org/ ag-ai/ ahuramazda/ ahuramazda.html, accessed 13 October 2011); “NSU Wankel Spider” (2008, NSU Prinz, www.nsuprinz. com/ Models /NSU_Spider.asp, accessed 7 October 2011); Masaaki Sato, The Honda Myth: The Genius and His Wake (New York: Vertical, Inc., 2006), and The Toyota Leaders: An Executive Guide, trans. Justin Bonsey (New York: Vertical, Inc., 2008); “Showroom Stock Sedans: The Nine Cars on the Track,” Car and Driver Vol. 17, No. 11 (May 1972), pp. 38-45; Eiji Toyoda, Toyota: Fifty Years in Motion (Tokyo: Kodansha International, 1987); the Wikipedia entries on the Bretton Woods system (en.wikipedia.org/wiki/Bretton_Woods_system, accessed 1 November 2011), Jim Downing (en.wikipedia.org/wiki/Jim_Downing, accessed 12 October 2011), Jujiro Matsuda (en.wikipedia.org/wiki/Jujiro_Matsuda, accessed 13 October 2011), the Mazda Capella (en.wikipedia.org/wiki/Mazda_Capella, accessed 28 October 2011), Mazda Cosmo (en.wikipedia.org/wiki/Mazda_Cosmo, accessed 16 October 2011), the Mazda Familia (en.wikipedia.org/wiki/Mazda_Familia, accessed 26 October 2011), Mazda Grand Familia (en.wikipedia.org/wiki/Mazda_Grand_Familia, accessed 3 November 2011), the Mazda Luce, en.wikipedia.org/wiki/Mazda_Luce, accessed 16 October 2011, the Mazda R100 (en.wikipedia.org/wiki/Mazda_R100, accessed 7 October 2011), the Mazda RX-2 (en.wikipedia.org/wiki/Mazda_RX-2, accessed 9 October 2011), the Mazda RX-3 (en.wikipedia.org/wiki/Mazda_RX-3, accessed 10 October 2011), NSU Motorenwerke (en.wikipedia.org/wiki/NSU_Motorenwerke, accessed 7 October 2011), the NS Savvanah (en.wikipedia.org/wiki/NS_Savannah, accessed 13 October 2011); The Return of Ultraman (en.wikipedia.org/wiki/The_Return_of_Ultraman, accessed 9 October 2011), and the SS Savannah (en.wikipedia.org/wiki/SS_Savannah, accessed 13 October 2011).

Some historical exchange rate data for the dollar and yen came from Lawrence H. Officer, “Exchange Rates Between the United States Dollar and Forty-one Currencies” (2011, MeasuringWorth, http://www.measuringworth.org/exchangeglobal/, used with permission). Exchange rate values cited in the text represent the approximate equivalency of Japanese and U.S. currency at the time, not the contemporary U.S. suggested retail prices, which are cited separately. Please note that all exchange rate equivalencies cited in the text are approximate; this is an automotive history, not a treatise on currency trading or the value of money, and nothing in this article should be taken as financial advice of any kind!


RELATED ARTICLES


36 Comments

Add a Comment
  1. The US RX-2 was updated for model year 1974 with the new single distributor engine. The car received the new taillight assembly and highly styled dashboard, but retained old style front end bodywork to accommodate the new large 5 mph bumpers. It was visually very distinct from the 1973 and earlier cars. It is a rare car because the RX-3 was cheaper and newer, and the new RX-4 had the luxury upscale side of the rotary market well covered.

    The first generation RX-3 12A engine 4-door sedan is a very rare car. The twin distributor 12A RX-3 was mostly sold in the US, and very few sedans were sold (which is why it was dropped for 1974). RX-3 coupes and wagons were the big sellers.

    The RX-3 may not have been a substantially better race car than the RX-2, but when Mazda got serious about sedan racing in about 1973 and 1974, the RX-3 was early in its model run, and the RX-2 was later in its cycle. It would make sense to “market” through racing success the car that was likely to be offered for a longer period of time. The RX-3 was also marketed as a “sporty” car and the RX-2 was more of a luxury car, though the mechanical specs were similar.

    Late in the RX-3’s production life, the US only RX3-SP was introduced, actually an 808 with the rotary engine and certain specific trim changes and driveline upgrades. The optional stripe and trim kit was manufactured in California and installed at the port. This iteration of the RX-3 encouraged grassroots racing of the rotaries and helped keep the rotary alive as a “sporty” engine until the arrival of the RX-7.

    1. Thanks for the clarification on the ’74 RX-2. Because of its rarity, detailed information on it was rather scarce.

      The Savanna wasn’t really that much younger than the Capella/RX-2 — the difference was less than 18 months — so I don’t know how much that really had to do with it. The Savanna had the potential for a better power-to-weight ratio in racing trim, and more advantageous dimensions. Aside from being substantially shorter (a plus in some types of event), the Savanna was actually 15mm wider than the Capella, and its tread width was 15mm/10mm greater, which makes for less body roll, even with stock suspension. Of course, they did pitch the Savanna at a different audience than the Capella, particularly in Japan.

      The RX-3SP is mentioned in the text. It’s not exactly an 808; the 808 was the export designation for the Grand Familia, which was the piston-engined version of the Savanna. Although Mazda marketed them as separate entities (rather than as a single line with a choice of piston or rotary power), my understanding was that the differences between the Savanna/RX-3 and comparable Grand Familia/808 weren’t any greater than the differences between the Capella/616 and RX-2 — larger fuel tank, some minor changes to accommodate the rotary’s exhaust system and emissions controls, etc. Six of one, half dozen of the other.

      Since I don’t think the RX-3SP arrived until after Mazda had already announced that they would be launching a new sports car, I assume you’re right that it was basically an appetizer for the RX-7. I don’t have production figures for the U.S. model, unfortunately, but Mazda listed total Savanna/RX-3 production as 9,825 units for the 1976 calendar year (encompassing part of the ’76 and ’77 model year) and 1,606 in 1977 (encompassing the latter part of ’77 and the ’78 model year), so it can’t have been a lot — although it’s clear there were at least enough to homologate it for IMSA and SCCA competition!

      1. The RX-3 was always distinct from the 808 in its interior fittings and dashboard. The SP’s interior is an exact duplicate of that year’s 808. There is actually no “rotary” badging except for the “Rotary Engine” badge on the trunklid (and the “RX3SP” on the right rear fender). The RX-3 always had chrome window driprails and rocker panel trim. Later 808s did not and neither did the SP. The SP taillight assemblies were parts binned from the Australian 808. Beyond the VIN, a fake SP is easy to tell if it is made from an earlier RX-3, but hard to tell from a late 808, if the bolt-on parts are changed. The 808 derivation of the SP is not supported by documentation, but instead by careful observation of how the various year RX-3s and 808s were put together.

        Keep in mind too, that by mid 1975, Rx-3s were essentially special order vehicles, manufactured in small batches. 808s were still being turned out in the tens of thousands per year. Which leads me to production numbers.

        Worldwide RX-3 production was recorded by calendar year. But US production was by model year, starting the previous August or September. Also, only US cars were included in the S124 serial number sequence (12A engine) until late 1973. Other markets got the 10A engine and a separate S102 serial number sequence until late 1973. Overall roughly 80,000 non-US market 10A engined (S102A) coupes and sedans were built, 75,000 US market 12A engined wagons (S124W), and about 85,000 mostly US but worldwide 12A engined coupes and sedans (S124A) were built.

        Here is what makes the understanding of production numbers difficult. Most RX-3 US production for a given model year is actually produced in the last part of the prior calendar year. So the calendar 1976 production is largely 1977 model year cars for the US. The other thing to keep in mind is that from late 1973 through mid 1976, the 12A engined production sequence (S124A) is not just the US any more, but represents worldwide production.

        So US sales for the early twin distributor car through late 1973 were about 60,000 coupes & sedans (S124A) and 55,000 wagons (S124W). Worldwide, about 20,000 of the second generation coupes and sedans were sold in 1974 and 1975. The 1976 “Savanna” model (special taillights and the introduction of the ‘air dam’ front lower valance) totals about 2,000 cars worldwide. The SP (US only) totalled about 3,000 for 1977 and 800 for 1978. Most of the 1977s were built in late 1976 and the 1978s were built in the fall of 1977. All continued the S124A serial number sequence, out to just over car number 85,000 (VIN S124A-185000). So those last 25,000 cars or so were sold worldwide, not just in the US. That is why the later cars are so hard to find in the US or anywhere else.

        Just to confuse things further, a small batch of “V-100” cars were built for Japan. They are essentially right hand drive RX3SPs, right down to the big bumpers, but with alternate badges. But rather than using the S124A VINs in sequence, they pick up the numbers in the 460000 range. I do
        not recall the prefix used, but the last part of the number appears to be in sequence with the 808s of the time. Perhaps the US cars stayed in the RX-3 sequence to satisfy the US authorities. The V-100 VIN sequence also suggests the late rotaries were a batch pulled from the 808 production.

        1. Given the slowdown in sales, it would make sense that later Savannas and RX-3s would have greater commonality with the piston-engined cars. During that period, Toyo Kogyo was also trying to increase inter-model commonality in general, as part of the effort to reduce unit costs. Different dashboards are expensive, especially for what’s become a slow-selling specialty model.

          If I may ask, where do your production numbers come from? I wasn’t able to get U.S. production breakdowns from Mazda, and the only figures I have there are model year totals that aren’t divided by model. Mazda’s figures only show total worldwide calendar year production, and the numbers I have are only for rotary models. (I asked about piston-engined cars, but wasn’t able to get that information.) I realize there’s a big discrepancy between model year and calendar year production (which among other things makes it hard to tell how many might belong to each model year, or each generation in years where they overlap).

          Thanks again for the info!

          1. The RX-3 is the only older rotary in which the US model year sales can be roughly discerned. Every other model uses one VIN series worldwide, with no country by country breakdown. Because for most of its production life, the RX-3 used separate VIN sequences for the US (due to the larger engine size), the US sales can be estimated, and also by model year.

            I use Mazda’s old dealer manuals that include VIN sequences as part of the model/year ID process at the dealer level. I guesstimate the numbers from memory, but now I have the books in front of me.

            Total cars about 240,000. Early non-US 10A engines, about 80,000. Early 12A US 55,999 coupes/sedans plus 50,103 wagons. So the total early cars about 186,000 of the 240,000 total. Second generation (now worldwide) roughly 27,000 coupes/sedans plus 22,000 wagons. This figure includes the “Savanna” cars.

            Finally, roughly 4,000 US RX3SPs (more than people think there were) and maybe? 1,000 Japanese V-100s.

            Roughly 2/3 of the second generation 27,000 are probably US, but a maximum of 1,845 of the US cars are the model year 1976 “Savanna” style (but still badged as RX-3, not Savanna). That one is the rarest US car, and very hard to find here (The US version did not get the alternate dashboard package on that model). It is the one style more abundant abroad rather than in the US, but still not common anywhere.

          2. Okay, that makes sense. Serial number sequences aren’t always 100% accurate (sometimes numbers are skipped for various reasons, or used out of sequence, etc.), but it’s certainly a reasonable basis for estimation.

            The figure Mazda provided for total worldwide Savanna/RX-3 production is 285,887, starting in calendar year 1971 and ending in 1977. Unfortunately, they didn’t have any sort of model breakdown.

  2. The maintenance and repair of the rotary engine was carefully planned at the dealer level as the cars were introduced. It was assumed that the dealers would disassemble the engines to replace the “wear parts” and gaskets at specified intervals. Special disassembly tools and procedures were put into place.

    In fact, the engines had a multitude of issues, and a variety of unplanned catastrophic failures (partly due to improper or poor owner maintenance habits). The orderly disassembly of engines was cancelled and an engine exchange program was introduced. The old core engines would be rebuilt with new parts by Mazda and cycled back into the dealer pipeline.

    The US engine license with Curtiss-Wright did not allow for engines to be purchased separate from a whole car, so the engine exchange was the way things had to be done. One could not go to Mazda and purchase a whole engine, not even a competition engine (which could be purchased outright in Japan). Only parts could be bought and built up into an engine, or a rebuilt engine could be swapped into a car for the old one.

    On the engine exchange program, the car’s VIN had to be recorded by the dealer and turned in to Mazda with the core engine, in order to get a new one (again, the C-W license restrictions). While Mazda may or may not have made money on the engine exchanges, the dealers certainly made money, and competed for the business. Some enterprising dealers went to the junkyards and pulled whole engines, while carefully recording the junked vehicles’ VINs, so they could stockpile new engines ahead of time and offer quicker turnaround to the customers. Years later, 10A and early 12A engines could sometimes be found in dealers’ back rooms, still sealed in the boxes, and were let go for a song to clear the space of unwanted inventory.

    1. Interesting — thanks for the info!

  3. The Cosmo RX-5’s profile was echoed by the later 1977-1979 Ford Thunderbird, though the RX-5’s “opera” window actually rolls down, unlike the T-bird’s fixed glass.

  4. I was waiting with bated breath for the second part of this series.

    Have you seen the (in)famous Mazda "boinger" commercial?

    Neat bit of rotary-related ’70s camp.

    1. That is pretty funny — I knew they did commercials along those lines, but I hadn’t seen that one.

  5. The early RX-3s had a strange quirk that could be pretty frightening if you weren’t prepared for it. Suddenly let up on the gas after a long hard blast and the car would backfire apparently from the thermal reactor – it sounded like a 12-gauge shotgun going off under the car and one would expect to see pieces of the exhaust system left behind on the road. That wasn’t the case, but it was still pretty unnerving.

    1. A lot of the period reviews noted something similar. It appears that it was a side effect of the rich mixtures used to increase the reactor’s effectiveness, and that when you closed the throttle, it momentarily jumped from rich to [i]very[/i] rich, causing the backfiring when unburned fuel hit the hot thermal reactor.

  6. It’s uncanny how much the Capella resembles the Renault 12, in the overall appearance apart from the coke-bottle kink there are a lot of similarities in the grille, rear end and roof profile/c-pillars

    1. Wow, that hadn’t occurred to me, but I agree. The sedan, in particular; the Capella coupe still looks more Alfa-like to me, but the sedan’s resemblance to the 12 is pronounced.

  7. I had an RX3-SP and ruled the streets for awhile in my College Neighborhood of Northridge, California back around 1978. Loved how the Mazda magazine car ads claimed the ‘SP’ did not stand for ‘slow poke’. The specs claimed my RX3-SP could ‘stick’ a Boss 302 V8, and it really did. Before my ride got ‘totaled’ in a car wreck with a Lady from Texas, I was slowly converting my Mazda for weekend Amateur Racing. Had the car ‘dropped’ a bit and added high performance Koni Shocks. The engine was stock, with the big Rotary engine seal replaced, under some kind of Mazda ‘Re-call’ thing. She could easily hit 123mph on the 101 fwy when the fuzz weren’t around.

  8. Just Picked up a Nice 1978 RX3SP from Puerto Rico and had it shipped to Florida, my first one was back in 1977 in EL Paso Texas, while serving int he US ARMY,I have had all the models from the RX2 to the 1993 Mazda RX7, Mazda Rotary Pickup but none of them come close to what you really feel for the RX3SP, its a nice toy to have and to pamper and take care of. THe sound of a Rotary Engine Bride Ported and overlap is music to any Rotary Fan.
    Would like to post picture but I guess on this site it cannot be done. But Thanks for the memories.

  9. Going to high school in 1980’s Oregon, rotary powered Mazdas were a common sight. Including mine, there were at least three rotary pickups in the school parking lot on any given day. My yellow 1975 rotary truck (along with a new Cosmo) was purchased by my uncle in ’77 or ’78 from a warehouse of unsold inventory in Japan and shipped back by the navy.

    It was an epicly fun little truck, but had some very odd quirks. They had a significantly stronger suspension system than other late ’70s small pickups and had no trouble reaching freeway speeds with very heavy loads. The small hatch in the side of the bed behind the passenger door in your picture is where the battery lives. That would corrode quite badly over time. The exhaust system was also one of the heaviest I’ve ever seen. In addition to the standard exhaust pipe with mufflers and such, there was a small straight pipe directly from the thermal reactor. I was told that was a pressure relief pipe to keep the muffler from exploding when the engine backfired.

  10. Thanks for the write up, I don’t think I’ve ever seen or heard of the FWD rotary Luce, or even a piston 1500cc 1500, only seen sedans.
    4dr sedans no matter what the make are more common than coupes/hard tops.
    I bought Mazdas for all my first cars, a 1974 RX3 sedan I bought in 1992, then a lot of 808s for spares and run abouts while working on the RX3 (changed the 12A and 3spd auto to a 13B extend port and 5spd manual out of an RX5), I think I owned about 4 808s, saving the best panels from them when I got them taken away for scrap.
    Of course in 1993 I also bought a 1973 RX4 hard top for another project car.

    Still have them, but stripped down in parts as unfinished projects these days unfortunately, but couldn’t bare to get rid of them.

    Lots of old RXs are still around in Australia and Puerto Rica. If you search places like youtube for ‘mazda rotary cruise’ you’ll see and hear a lot still running on the roads.

  11. Largest Australian Holden was the Statesman, Premier was a shorter wheelbase. FAB site.

    1. Oops, you’re quite right. Thanks for the correction — I’ve amended the text.

  12. Looking for a picture of the Mazda rotary 4 door sedan I owned in the 1980s bought used in Upstate New York. The interior was really plush. I loved this car but it began to rust. Cannot remember the model name. I do not see it listed in this article. Thanks. Paul

    1. Well, if it was a U.S.-market car and a four-door sedan, it was either a) a 1972–1974 RX-3 (a.k.a. Savanna), b) a 1971–1974 RX-2 (a.k.a. Capella), or c) a 1974–1978 RX-4 (a.k.a. Mazda Luce), which are described in the article (although naturally I may not have a picture of the specific version you had).

      Based on the time frame and plushness, my guess would be the RX-4. The RX-4 (known as Luce in Japan and Mazda 929 in piston-engined export form) was the biggest and plushest rotary sedan Mazda sold in this country.

      If the car was RHD and not originally a U.S. model, it might also be a later Mazda Luce or the four-door hardtop version of the Cosmo (which is pictured in this article), which were never officially imported here, although a few have shown up as gray-market imports and there may be some in Canada. I’m assuming if you had a RHD car you would have mentioned it, though — generally, people who have RHD Japanese-market imports have a pretty good idea of what their car is! — so my guess would be the RX-4.

  13. My father had a 1978 RX-4 rotary. I used to ask for the keys to “go to a friends house”. In reality I was headed for hwy 100, the nearby cruise boulevard. Noticing that the rotary had a strong pull from around 3000 rpm and up I found a way to run with the muscle cars back then. The dark green 4 door was not quick off the line with an automatic transmission. I definitely had to avoid a drag race, but those were not as common as the 35-40 mph floor it till 60 mph or so bursts to see who could pull ahead by a fender length or more. That is where I realized that if the transmission was left in first gear the little rotary was in it’s power band. Many drivers were surprised by that little import and the strange screaming sound it made as it pulled ahead of them and then back firing when lifting off the gas. Running in first gear up and down the cruise strip on Fri. and Sat. nights eventually took it’s toll. After two summers of this kind of abuse I was able to leave a smoke screen under certain conditions. Interestingly my father though I was putting gas in the car as he kept business mileage records. Maybe fuel efficiency was better at higher rpms. It sure liked to rev. Power band like a two stroke dirt bike, not much initially but hang on when it starts to pull.

  14. I too had a 1978 Rx3-SP. $4500 new. 5speed stick. Got it up to 125mph a few times. Beat a few 350cu in V-8 vettes, and could hold the lead up to about 100mph. It was a rocket off the line, and light weight (in lbs) car. Vettes were heavy V8 iron engine dogs, even with Fiberglas bodies.
    Rarely ever lost a race in 5years in the suburbs of Chicago, to any car.

    Car rarely needed service. But you had to replace the plugs every 6mos. Due to oil by design was injected into rotary “cylinders” for lube.
    I cleaned them religiously 3mos, and replaced them every 6mos, with OEM Mazda plugs, which cost $3 each….2x normal plugs at the time.
    Rotary engines were awesome. I really thought they were the future, and not camshaft cylinders. Oh well, bring on the Electric cars!

    1. As I understand it, the plugs in a rotary engine inevitably lead a fairly hard life because they’re buried in the “combustion chamber” area of the housing. In a reciprocating engine, the tip of the plug is exposed to uncompressed intake air during each intake stroke, but that’s not the case with a rotary, where the mixture is already compressed (and hot) before it gets to the plug. This is why the housings of (as far as I know) all production rotaries are aluminum: the aluminum is more conductive to heat than iron, and without that, the housing ends up cracking due to thermal stress. (This happened to various test engines using cast iron housings, which in certain other ways would have been preferable.)

  15. hello how many us 1973 rx3 sedans were made cause I have one

    1. I’m afraid I’ve been unable to find sales breakdowns by model or body style — sorry! I wish I knew.

    2. A U.S. model 12A engine sedan is more rare, and a rest-of-world 10A engine sedan is more common. The U.S. version was the only one with the 12A engine in 1973 (twin distributors), and while the rest of the world bought quite a few RX3 sedans, the U.S. buyers preferred coupes and wagons. As all true RX3s have become quite rare these days, rest assured that the car is not common any more, in any case. Basically all parts of the car are fragile (paint, interiors, sheet metal, trim, engines), and do not hold up well to abuse, poor maintenance habits, or exposure to the outside elements.

      I believe 1973 was the last year for RX3 sedans in the U.S., but I could be wrong about that.

      1. On the last point, as best I can determine that is correct, but I’m not positive either.

  16. From 1974-1976, I worked for Tilton Mazda in Sioux Falls, SD. At that time I bought a new 1975 RX-3. I found the window sticker about 3 months ago. WOW! Prices were: dealer prep $50.00, Freight $85.00. The AM radio set me back $69.00. MSRP for a Flare Yellow 2-Dr was $3697.00. Total was $3901.00. It listed the Engine No.as 12AS57958. The sticker was printed 5/19/75 and I bought it in July 1975. As I recall I paid $3500.00. This car was a blast to drive. It came with white vinyl interior, did they offer black? That engine was so smooth. I loved the buzzer to let you know when to back off.

    1. Many of the RX-3s I’ve seen have had black vinyl interiors, so I’m guessing the answer to your question is yes, although white might be slightly less painful on a hot summer afternoon!

  17. Back in around 1978 I was in Taupo, New Zealand. One day I heard a banshee wail, clearly a Rotary in the distance. It took quite some time to come into view. Eventually there was a Mazda Ute, resplendant in the company blue and white livery, with a pretty radical exhaust. I did not know that rotary utes were ever issued, this being s right hand drive one was probsbly concerted from a B1600. This dealer’s workshop vehicle had a VERY overloaded B1600 on the other end of a tow rope. With little torque and heaps of revs in low gear the whole cavalcade crawled into view with a cacophany that all Taupo heard. It was a ROTARY!

  18. i hav a 72 rx3 series 2 with a ground up rest which im selling for 8 grand the car is a solid rust free car with a canary yellow paint fresh rebuilt motor 12a mild streetport rotor rims 13 inch and mickey thomsons in the rear the car is really fast call me if interested my name is melvin from chelsea massachusetts 02150

    1. Hey Melvin,

      I redacted your phone number — if you really want to publish it, let me know and I’ll put it back, but I take no responsibility for any consequences. (I don’t know about you, but I hate spam calls!)

  19. When the RX2 was released here in Oz, guys I knew would go to the dealer for a test drive, and see if the chaperone who rode with them knew what the over-rev buzzer meant! I also used to go to sedan car races when Alan Moffat’s RX7 was running – boy did it have a sharp barking exhaust note! Especially when being scrutineered under a tin roof!

    jp

Leave a Reply

Your email address will not be published. Required fields are marked *

Click here to read our comment policy. You must be at least 18 to comment. PLEASE DON'T POST COPYRIGHTED CONTENT YOU AREN'T AUTHORIZED TO USE!
Except as otherwise noted, all text and images are copyright © Aaron Severson dba Ate Up With Motor. (Terms of Use – Reprint/Reuse Policy) Trademarks referenced herein are the property of their respective owners and are used here for informational/nominative purposes.